186 | Pioneer 12 instruction

Integrator Mode

7INPUT3

MENU

¥CONTRAST ¥BRIGHTNESS ¥COLOR ¥TINT ¥SHARPNESS ¥H. POSITION ¥V. POSITION ¥COLOR TEMP. ¥DNR ¥MPEG NR ¥CTI ¥PURECINEMA

INPUT3–SIGNAL#1

(INPUT3 is effective only when a PDA-5003/PDA- 5004 is installed.)

Note

When a PDA-5003/PDA-5004 is installed, the values are stored in memory for both a 50 Hz video signal and 60 Hz video signal.

INTEGRATOR

¥CONTRAST ¥BRIGHTNESS ¥COLOR ¥TINT ¥SHARPNESS ¥C. DETAIL RED

¥C. DETAIL YELLOW ¥C. DETAIL GREEN ¥C. DETAIL CYAN ¥C. DETAIL BLUE

¥C. DETAIL MAGENTA ¥R. HIGH

¥G. HIGH

¥B. HIGH

¥R. LOW

¥G. LOW

¥B. LOW

¥H. POSITION

¥V. POSITION ¥H. SIZE

¥V. SIZE

¥GAMMA

INPUT3–SIGNAL##A

(COLOR MODE; NORMAL)

¥CONTRAST ¥BRIGHTNESS ¥COLOR ¥TINT ¥SHARPNESS ¥C. DETAIL RED

¥C. DETAIL YELLOW ¥C. DETAIL GREEN ¥C. DETAIL CYAN ¥C. DETAIL BLUE

¥C. DETAIL MAGENTA ¥R. HIGH

¥G. HIGH

¥B. HIGH

¥R. LOW

¥G. LOW

¥B. LOW

¥H. POSITION

¥V. POSITION ¥H. SIZE

¥V. SIZE

¥GAMMA

INPUT3–SIGNAL##A

(COLOR MODE; STUDIO)

186

Image 186

Pioneer 12 technical manual 186

Contents

Technical Manual Ver To use this product safely Table of Contents Table of Contents Introduction PrecautionsRGB signals from AV devices other than PCs Input Features and Functions of this device Specifications Refresh rate Input Response SignalsPC signals supported Dot x Line Vertical External Dimensions Light Sensor for the remote/ambient light Sensor/indicator Main Unit Operation PanelConnection panel Controls and Connectors Main unit Operation panel on the main unitMain unit 567 Plasma Display Section Video Card PDA-5003 Section Video Card PDA-5004 Section Pin layout INPUT1 Mini D-sub, 15-pin connector female Pin layoutINPUT2 DVI-D 24 pin connector female Pin layout Combination IN/OUT terminal pin layout Remote Control Unit Installation Site Requirements Safety Precautions Effective remote control distance Temperature and humidity conditionsPower requirements Prevent condensation Installation Conditions Heat dissipation Rear view diagram Side view diagram Calculating heat quantityProduct mounting holes Methods of securing Mounting surface warping Unpacking Installation ProceduresTransportation precautions Ref. No Terms Wiring To attach the speed clamps to the main unit Organize cables together using the provided speed clampsUsing pliers, twist the clamp 90 and pull outward To remove speed clamps Ambient Temperature 0 C to 40 C examples 1 Special Installation Mounting to fittingsOperating environment for standard installation Operating environment for vertical installation *1 Vertical installation Example Requirements when used with PDP-S55-LR speaker system Special Instruction Hanging on the wallHanging on the wall Wall-mounted installation Special Installation Hanging on the wallFlush-wall installation Wall-embedded installation Embedding in the wall Special Installation Embedding in the wallOperating Temperature Restrictions Viewed from Above Thermometer temperature measurement point Embedding in walls with no space provided behind the unit Usage temperature conditions BOX air temperature Special installation When the display is put in a boxWhen the display is put in a box Ambient temperature 0 C to 35 C Special Installation Ceiling suspension with wires Ceiling suspension with wiresAmbient Temperature 0 C to 40 C Special Installation Ceiling suspension with wires Special Installation Hanging on the wall lengthwise Operating Temperature Restrictions *1Hanging on the wall lengthwise Installation is not possible Temperature in space X and Y Mm to 370 mm Viewed from Above Viewed from the Right SidePage Embedding in walls with no space provided behind the unit Page Special Installation Installed facing upward Installed facing upwardHorizontal surface Operating Temperature Restrictions *1 Usage temperature conditions *1 Special installation Horizontal connections Horizontal connectionsMm or more To 40 C Special installation Multiple MultipleMm to 300 mm or less To 35 C Mm or more To 40 C ¶ Table Top Stand PDK-TS26 Standard Mounting Components Features and Characteristics¶ Video Card PDA-5003/PDA-5004 ¶ Wall Mount Unit PDK-WM03 Handling precautions Precautions for installation contractorsHandling the Standard Mounting Components Specifications Video Card PDA-5003/PDA-5004 Accessories PDA-5004 Video-related External Dimensions PDA-5003PDA-5004 Connection panel when equipped with PDA-5003 Connection panel when equipped with PDA-5004 Installation Installing proceduresInstallation Notes Impedance selector switch is found only on the PDA Remove the two screws holding the video card Holding the inside tabs, pull the video card straight out When using PDA-5004 Input connectors on the Plasma Display with video cardWhen using PDA-5003 Connection to INPUT1 and INPUT5 When connecting to Analog RGB INPUT5 When connecting to Analog RGB in INPUT1On-screen setup is necessary after connection When connecting to Component Video INPUT5 Connection of G on Sync analog RGB source Connection of composite Sync analog RGB Source Connection of separate Sync analog RGB Source When connecting to Analog RGB OUT INPUT1 To an external monitor INPUT1 Connection to INPUT4 Connection to INPUT2Connection to INPUT3 Computer or AV component Video Video signal Signal type Signal formatAbout DTV set top box connection Audio connections Audio connection for component connected toAudio connections for component connected to INPUT3 Signal Format Remark Input 1 Applies only when equipped with PDA-5003/PDA-5004 Vertical Horizontal Signal Remark Package dimensions Table Top Stand PDK-TS26Other factors External Dimensions When using Plasma Display Stand assembling Attaching the Stand to the Plasma Display Wall Mount Unit PDK-WM03 ComponentsAttachment Restrictions Center of the display Hardware assembly and Plasma Display attachment Installing the hung on wall unit on the wallAttaching the metal fittings Installing the Plasma Display Speaker System PDP-S55-LR External Dimensions when mounted to the Plasma Display Installation on the Plasma Display Installation procedureInstall the speaker system according to the steps 1 through Speaker System PDP-S55-LR Care and Maintenance When the cabinet gets dirty Speaker System PDP-S55-LR Before Beginning Adjustment Operation Mode Before Beginning Adjustments List of Input Correspondence Signals Input correspondence signals personal computer signals Resolution Refresh rate Not available DOT by DOT Screen size Personal computer signalScreen size Full INPUT1, INPUT5 Signal Format Screen size Remark Screen size Signal Format 640x480 59.9 Hz 31.5 kHz INPUT2 Refresh rate Screen size Dot x line When a video card is installed Personal computer Screen size List of Adjustable and Settable Items Menu Mode PDP-607CMX Before Beginning Adjustments PDA-5003/PDA-5004 Slot card other than PDA-5003/PDA-5004 Integrator mode PDP-607CMX Applicable only when a PDA-5003/PDA-5004 is installed PDA-5003/PDA-5004 Slot card other than PDA-5003/PDA-5004 Last Memory AgingSaving to Memory Normal Operating Mode Normal Operation Mode About normal operation mode149 351 Normal Operating Mode Side-by-side OFF Picture-in-pictureLower right Upper right Lower left Concerning the display of the OSD of each item Menu ModeAbout menu mode Images shown here may differ from the actual display image Press the Menu button to display the menu screen Example of a Menu Mode OperationRemote control unit Press the SET button Adjustment and setting in the Menu Mode Power Management SettingOFF on Signal Format Setting Others ....... Selectable resolutions are displayed ScreenAuto Others Menu Language Display Setting Resolution KHz Signal format Remarks Polarity Standard Energy Saving SettingTo cancel MUTE, press the Menu button, Input button etc MODE1, MODE2 MODE3 Mute ‘ENERGY SAVE’ setting is common for all inputs Screen MODE1 MODE2MODE3 Timer Setting Program/Repeat Timer SettingDaylight Saving Time Orbiter Setting OFF MODE1 MODE3 MODE2 Soft Focus Setting ‘SOFT FOCUS’ setting is common for all inputs Screen Auto Set Up Mode Setting Auto SET UP Mode Screen Position, Clock Frequency and Clock Phase Adjustment Example When a PC signal is input to INPUT1 1024 x 113 Auto Function Mode Setting As shown below PIP Detect Setting ‘PIP DETECT’ setting is common for all inputs Split Freeze Setting ‘SPLIT FREEZE’ setting is common for all inputsOFF By S PIP Press the Menu button to display the menu Item Applicable only when a PDA-5003 PDA-5004 is installedConcerning the display of the OSD of each Screen Color Temperature Setting HighLOW Place the cursor over ‘POWER Management Auto Power Management and Auto Power OFF SettingOFF/DISABLE Power OFF’ and change the setting with the SET DNR digital noise reduction Setting MiddleOFF High 2 3 Middle 2 3 LOW Mpeg NR Setting CTI Setting Conversion is performed without Purecinema SettingOFF I/P is converted Input Correspondence Signal OFF Color Decoding Setting INPUT1, INPUT2, INPUT5Connected Color System Setting INPUT4 Auto 127 128 PC 2 3 Video DVI SettingPLUG/PLAY PC LOW 0 to 255 High 16 to 235 130 131 132 Adjust each item by pressing the 5/ ∞/ 2/ 3 buttons OFF Disables Daylight Saving Time modeWeek Set current day of the week 134 135 136 137 138 139 140 141 Integrator Mode About the Integrator Mode Example of Integrator Mode Operation To continue with adjusting another item, repeat steps 5 to Adjustment and Setting in the Integrator Mode Picture AdjustmentFor video signal input White Balance Adjustment Color Detail setting Use the 5/ ∞ buttons to switch between items Screen Gamma Setting 31.8 Screen Screen Position Adjustment Screen For PC signal inputPosition H. Position Clock H. Position Clock Phase 149 SUB Volume Setting Audio block diagram concept diagram To reset the program Program Timer SettingProgram timer settings To clear the set contents Viewing the program timer screen Screen Mask Setting Side Mask Setting Auto Side Mask OFF 155 Setting Method Setting the ID NO. SET Video Wall SettingPosition Type Normal Auto ID OFF On Delay ABL Link Setting the screen divider ID positions for nine panels Setting the positionSetting the display mode ID positions for 16 panels Second Setting the Power on DelayTurns on the power approximately every Displays turns on at the same time Setting the ABL Link Baud Rate Setting 01H to FFH ... The ID number is set to the designated Remote Control IDAssigning an ID Number 162 Cooling Fan Control Setting ‘FAN CONTROL’ setting is common for all inputs ScreenMAX OSD Display Setting Setting the Screen displaySetting the Screen size 165 Front Indicator Setting On Normal LED function OFF Lights red during standby ScreenOn OFF Color Mode Setting ‘COLOR MODE’ setting is common for all inputs Image Process Normal Signal Type Motion PRO USE SettingFactory setting Underscan Image Process Blue only PureMono Tone High CNT FRC Setting ‘FRC’ setting is common for all inputs ScreenChanges the frame rate Applicable only when a PDA-5003 or PDA-5004 is installed VIDEO/PC Power on Mode Setting VolumeLast INPUT1 Multi INPUT2 INPUT1 2 3INPUT2 2 3INPUT3 INPUT5 2 3INPUT4 Setting when Multi is selectedINPUT1 INPUT2 Last 2 3 0 to 42 SELECT2 Seamless SW SettingSELECT1 Seamless SW Mirror Mode Setting ‘MIRROR MODE’ setting is common for all inputs Screen By S Layout Multiscreen SettingBy S Size PIP Size Fade PIP Side by SIDE4 Side by SIDE1 Side by SIDE2Side by SIDE3 Side by SIDE5 179 Repeat Timer Setting Setting the single screen Repeat Timer Setting the two screen Repeat Timer Setting the Video Wall Repeat Timer Functional Lock ‘BUTTONS LOCK’ ‘IR LOCK’ ‘BUTTONS & IR LOCK’ ‘MEMORY LOCK‘ Center Position Display 184 185 186 187 188 RS-232C Adjustment About the RS-232C Adjustment TXD RXD RTS GND CTS InterfaceRXD TXD CTS TXD RXD RTS GND Combination Connection Connection methodConnect the panels as shown in the figure below ID Assignment Precautions when assigning IDsID is assigned from the PC Commands IDC ID Clear IDS ID SET 193 Normal Operation Related Commands Input Select RS-232C Adjustment MENU-SETUP related commands MENU-OPTION related commands Signal Format INTEGRATOR-PICTURE related commands INTEGRATOR-SCREEN related commandsINTEGRATOR-SETUP related commands INTEGRATOR-OPTION related commands Screen Mask 199 Other commands PIP fade in function effective 201 Quest Commands Quest Command Table Data Content Obtaining QST Status Information QWB Obtaining integrator/WHITE Balance information Data Content Size RemarksQPI Obtaining Integrator/PICTURE information QPS Obtaining integrator/SCREEN information QSS Obtaining Setup information QSO Obtaining menu integrator/OPTION information Main screen input function Main screen size QSU obtaining the audio status QCI Obtaining time informationQAP Obtaining machine name Table of commands not compatible with PDP-505CMX COF Check Sum Example 1 When the data is missing 1 ByteExample 2 When 1 Byte of data in the data is unreadable Examples of check sum applications Screen Burning Setting example Setting with Menu Mode To enjoy using your plasma display for many yearsStandard Functions Settings cannot be changed Setting with Integrator Mode These data are reference values they cannot be ensured Concerning frame delay lip syncVideo input signal Input vertical Frame delay Number Precautions Error Message RemedySelf-diagnosis Function Connection procedure Cabinet and Remote-control UnitDisconnect and Remove Hardware Screen front protection panel MaintenanceReadjustment of the White Balance Vents