Refresh rate Screen size Dot x line | Pioneer 12 specs

Before Beginning Adjustments

									: Not available.

Resolution	Refresh rate			Screen size (Dot x line)				Remarks
(Dot x Line)	Vertical		Horizontal	DOT BY DOT	4:3	FULL		Remarks
	Vertical		Horizontal	DOT BY DOT	4:3	FULL

1024x768	60 Hz		48.4 kHz	1024x768		1365x768
				1024x768		1365x768
	60 Hz		49.7 kHz	±		±		Work station (SGI)
	70.1 Hz		56.5 kHz	±		±
	75 Hz		60.0 kHz	±		±
	85 Hz		68.7 kHz	±		±
	100.6 Hz		80.5 kHz	±		±
	119.4 Hz		95.5 kHz	±		±
1280x768	56.2 Hz		45.1 kHz	1280x768		1365x768
				1280x768		1365x768
	59.8 Hz		48 kH z	±		±
	69.8 Hz		56 kH z	±		±
1280x800	59.8 Hz		49.7 kHz			1365x768
						1365x768
1280x854	60 Hz		53.1 kHz
						1365x768
1360x768	60 Hz		47.7 kHz	1360x768				I/O DATA
				1360x768		1365x768
1376x768	59.9 Hz		48.3 kHz					I/O DATA
						1365x768
1152x864	60 Hz		53.7 kHz
					1024x768	1365x768
	72 Hz		64.9 kHz		±	±
	75 Hz		67.5 kHz		±	±
1152x900	66 Hz		61.8 kHz		1024x768	1365x768		Sun Microsystems LO
					1024x768	1365x768
	76 Hz		71.7 kHz		±	±		Sun Microsystems HI
1440x900	59.9 Hz		55.9 kHz			1365x768		Apple Macintosh17”
						1365x768
1280x960	60 Hz		60.0 kHz		1024x768	1365x768
					1024x768	1365x768
	85 Hz		85.9 kHz		±	±
1280x1024	60 Hz		63.9 kHz		1024x768	1365x768		Work station (SGI)
					1024x768	1365x768		Work station (SGI)
	60 Hz		64.0 kHz		±	±
	60 Hz		64.6 kHz		±	±		Work station (EWS4800)
	71.2 Hz		75.1 kHz		±	±		Work station (EWS4800)
	72 Hz		78.1 kHz		±	±		Work station (HP)
	75 Hz		80.0 kHz		±	±
	76.1 Hz		81.1 kHz		±	±		Work station (SUN)
	85 Hz		91.1 kHz		±	±
1400x1050	60 Hz		65.3 kHz		1024x768	1365x768
					1024x768	1365x768
	74.9 Hz		82.3 kHz		±	±
1680x1050	60 Hz		65.3 kHz
						1365x768
1920x1080	50 Hz		56.2 kHz
						1365x768
	60 Hz		67.5 kHz			±
1600x1200	60 Hz		75.0 kHz		1024x768	1365x768		CVT
					1024x768	1365x768
1920x1200RB*	60 Hz		74.0 kHz			1365x768
						1365x768
			: Optimal picture. Adjustment of picture position, refresh rate, phase etc., may be necessary.
			: Picture will be enlarged but some fine detail will be hard to see.
			: Simple reproduction. Fine detail will not be reproduced.
		RB*: Abbreviation for Reduce Blanking that is set by CVT.

Note

In rare cases, the picture may not translate properly when switching between compatible signal formats on the output device (PC, etc.). Should this happen, turn off the power and then turn it back on again.

88

Image 88

Pioneer 12 technical manual Refresh rate Screen size Dot x line

Contents

Technical Manual Ver To use this product safely Table of Contents Table of Contents Precautions RGB signals from AV devices other than PCsIntroduction Input Features and Functions of this device Specifications Input Response Signals PC signals supportedRefresh rate Dot x Line Vertical External Dimensions Main Unit Operation Panel Light Sensor for the remote/ambient light Sensor/indicatorConnection panel Main unit Operation panel on the main unit Controls and ConnectorsMain unit 567 Plasma Display Section Video Card PDA-5003 Section Video Card PDA-5004 Section INPUT1 Mini D-sub, 15-pin connector female Pin layout INPUT2 DVI-D 24 pin connector female Pin layoutPin layout Combination IN/OUT terminal pin layout Remote Control Unit Installation Site Requirements Safety Precautions Temperature and humidity conditions Power requirementsEffective remote control distance Prevent condensation Installation Conditions Heat dissipation Calculating heat quantity Rear view diagram Side view diagramProduct mounting holes Methods of securing Mounting surface warping Installation Procedures Transportation precautionsUnpacking Ref. No Terms Wiring Organize cables together using the provided speed clamps Using pliers, twist the clamp 90 and pull outwardTo attach the speed clamps to the main unit To remove speed clamps Special Installation Mounting to fittings Operating environment for standard installationAmbient Temperature 0 C to 40 C examples 1 Operating environment for vertical installation *1 Vertical installation Example Special Instruction Hanging on the wall Requirements when used with PDP-S55-LR speaker systemHanging on the wall Special Installation Hanging on the wall Flush-wall installationWall-mounted installation Wall-embedded installation Special Installation Embedding in the wall Operating Temperature RestrictionsEmbedding in the wall Viewed from Above Thermometer temperature measurement point Embedding in walls with no space provided behind the unit Special installation When the display is put in a box When the display is put in a boxUsage temperature conditions BOX air temperature Ambient temperature 0 C to 35 C Ceiling suspension with wires Special Installation Ceiling suspension with wiresAmbient Temperature 0 C to 40 C Special Installation Ceiling suspension with wires Operating Temperature Restrictions *1 Special Installation Hanging on the wall lengthwiseHanging on the wall lengthwise Installation is not possible Temperature in space X and Y Mm to 370 mm Viewed from Above Viewed from the Right SidePage Embedding in walls with no space provided behind the unit Page Installed facing upward Special Installation Installed facing upwardHorizontal surface Operating Temperature Restrictions *1 Usage temperature conditions *1 Horizontal connections Special installation Horizontal connectionsMm or more To 40 C Multiple Special installation MultipleMm to 300 mm or less To 35 C Mm or more To 40 C Standard Mounting Components Features and Characteristics ¶ Video Card PDA-5003/PDA-5004¶ Table Top Stand PDK-TS26 ¶ Wall Mount Unit PDK-WM03 Precautions for installation contractors Handling precautionsHandling the Standard Mounting Components Specifications Video Card PDA-5003/PDA-5004 Accessories PDA-5004 Video-related PDA-5003 External DimensionsPDA-5004 Connection panel when equipped with PDA-5003 Connection panel when equipped with PDA-5004 Installing procedures Installation NotesInstallation Impedance selector switch is found only on the PDA Remove the two screws holding the video card Holding the inside tabs, pull the video card straight out Input connectors on the Plasma Display with video card When using PDA-5003When using PDA-5004 Connection to INPUT1 and INPUT5 When connecting to Analog RGB in INPUT1 On-screen setup is necessary after connectionWhen connecting to Analog RGB INPUT5 When connecting to Component Video INPUT5 Connection of G on Sync analog RGB source Connection of composite Sync analog RGB Source Connection of separate Sync analog RGB Source When connecting to Analog RGB OUT INPUT1 To an external monitor INPUT1 Connection to INPUT2 Connection to INPUT3Connection to INPUT4 Computer or AV component Signal type Signal format Video Video signalAbout DTV set top box connection Audio connection for component connected to Audio connectionsAudio connections for component connected to INPUT3 Signal Format Remark Input 1 Applies only when equipped with PDA-5003/PDA-5004 Vertical Horizontal Signal Remark Table Top Stand PDK-TS26 Package dimensionsOther factors External Dimensions When using Plasma Display Stand assembling Attaching the Stand to the Plasma Display Components Wall Mount Unit PDK-WM03Attachment Restrictions Center of the display Installing the hung on wall unit on the wall Hardware assembly and Plasma Display attachmentAttaching the metal fittings Installing the Plasma Display Speaker System PDP-S55-LR External Dimensions when mounted to the Plasma Display Installation procedure Installation on the Plasma DisplayInstall the speaker system according to the steps 1 through Speaker System PDP-S55-LR Care and Maintenance When the cabinet gets dirty Speaker System PDP-S55-LR Before Beginning Adjustment Operation Mode Before Beginning Adjustments List of Input Correspondence Signals Input correspondence signals personal computer signals Resolution Refresh rate Not available Screen size Personal computer signal Screen sizeDOT by DOT Full INPUT1, INPUT5 Signal Format Screen size Remark Screen size Signal Format 640x480 59.9 Hz 31.5 kHz INPUT2 Refresh rate Screen size Dot x line When a video card is installed Personal computer Screen size List of Adjustable and Settable Items Menu Mode PDP-607CMX Before Beginning Adjustments PDA-5003/PDA-5004 Slot card other than PDA-5003/PDA-5004 Integrator mode PDP-607CMX Applicable only when a PDA-5003/PDA-5004 is installed PDA-5003/PDA-5004 Slot card other than PDA-5003/PDA-5004 Aging Last MemorySaving to Memory About normal operation mode Normal Operating Mode Normal Operation Mode149 351 Side-by-side OFF Picture-in-picture Normal Operating ModeLower right Upper right Lower left Menu Mode About menu modeConcerning the display of the OSD of each item Images shown here may differ from the actual display image Example of a Menu Mode Operation Remote control unitPress the Menu button to display the menu screen Press the SET button Power Management Setting Adjustment and setting in the Menu ModeOFF on Others ....... Selectable resolutions are displayed Screen Signal Format SettingAuto Others Menu Language Display Setting Resolution KHz Signal format Remarks Polarity Energy Saving Setting To cancel MUTE, press the Menu button, Input button etcStandard MODE1, MODE2 MODE3 Mute MODE1 MODE2 ‘ENERGY SAVE’ setting is common for all inputs ScreenMODE3 Program/Repeat Timer Setting Timer SettingDaylight Saving Time Orbiter Setting OFF MODE1 MODE3 MODE2 Soft Focus Setting ‘SOFT FOCUS’ setting is common for all inputs Screen Auto Set Up Mode Setting Auto SET UP Mode Screen Position, Clock Frequency and Clock Phase Adjustment Example When a PC signal is input to INPUT1 1024 x 113 Auto Function Mode Setting As shown below PIP Detect Setting ‘PIP DETECT’ setting is common for all inputs ‘SPLIT FREEZE’ setting is common for all inputs Split Freeze SettingOFF By S PIP Item Applicable only when a PDA-5003 PDA-5004 is installed Concerning the display of the OSD of eachPress the Menu button to display the menu Screen High Color Temperature SettingLOW Power Management and Auto Power OFF Setting OFF/DISABLEPlace the cursor over ‘POWER Management Auto Power OFF’ and change the setting with the SET Middle DNR digital noise reduction SettingOFF High 2 3 Middle 2 3 LOW Mpeg NR Setting CTI Setting Purecinema Setting OFFConversion is performed without I/P is converted Input Correspondence Signal OFF INPUT1, INPUT2, INPUT5 Color Decoding SettingConnected Color System Setting INPUT4 Auto 127 128 DVI Setting PLUG/PLAY PCPC 2 3 Video LOW 0 to 255 High 16 to 235 130 131 132 OFF Disables Daylight Saving Time mode Adjust each item by pressing the 5/ ∞/ 2/ 3 buttonsWeek Set current day of the week 134 135 136 137 138 139 140 141 Integrator Mode About the Integrator Mode Example of Integrator Mode Operation To continue with adjusting another item, repeat steps 5 to Picture Adjustment Adjustment and Setting in the Integrator ModeFor video signal input White Balance Adjustment Color Detail setting Use the 5/ ∞ buttons to switch between items Screen Gamma Setting 31.8 Screen For PC signal input Screen Screen Position AdjustmentPosition H. Position Clock H. Position Clock Phase 149 SUB Volume Setting Audio block diagram concept diagram Program Timer Setting Program timer settingsTo reset the program To clear the set contents Viewing the program timer screen Screen Mask Setting Side Mask Setting Auto Side Mask OFF 155 Video Wall Setting Position Type Normal Auto ID OFF On Delay ABL LinkSetting Method Setting the ID NO. SET Setting the screen divider Setting the position Setting the display modeID positions for nine panels ID positions for 16 panels Setting the Power on Delay Turns on the power approximately everySecond Displays turns on at the same time Setting the ABL Link Baud Rate Setting Remote Control ID Assigning an ID01H to FFH ... The ID number is set to the designated Number 162 ‘FAN CONTROL’ setting is common for all inputs Screen Cooling Fan Control SettingMAX Setting the Screen display OSD Display SettingSetting the Screen size 165 On Normal LED function OFF Lights red during standby Screen Front Indicator SettingOn OFF Color Mode Setting ‘COLOR MODE’ setting is common for all inputs PRO USE Setting Factory setting UnderscanImage Process Normal Signal Type Motion Image Process Pure Mono ToneBlue only High CNT ‘FRC’ setting is common for all inputs Screen FRC SettingChanges the frame rate Applicable only when a PDA-5003 or PDA-5004 is installed VIDEO/PC Volume Power on Mode SettingLast INPUT1 Multi INPUT2 Setting when Multi is selected INPUT1 INPUT2INPUT1 2 3INPUT2 2 3INPUT3 INPUT5 2 3INPUT4 Last 2 3 0 to 42 Seamless SW Setting SELECT1SELECT2 Seamless SW Mirror Mode Setting ‘MIRROR MODE’ setting is common for all inputs Screen Multiscreen Setting By S SizeBy S Layout PIP Size Fade PIP Side by SIDE1 Side by SIDE2 Side by SIDE3Side by SIDE4 Side by SIDE5 179 Repeat Timer Setting Setting the single screen Repeat Timer Setting the two screen Repeat Timer Setting the Video Wall Repeat Timer Functional Lock ‘BUTTONS LOCK’ ‘IR LOCK’ ‘BUTTONS & IR LOCK’ ‘MEMORY LOCK‘ Center Position Display 184 185 186 187 188 RS-232C Adjustment About the RS-232C Adjustment Interface RXD TXD CTSTXD RXD RTS GND CTS TXD RXD RTS GND Connection method Combination ConnectionConnect the panels as shown in the figure below Precautions when assigning IDs ID is assigned from the PC Commands IDC ID ClearID Assignment IDS ID SET 193 Normal Operation Related Commands Input Select RS-232C Adjustment MENU-SETUP related commands MENU-OPTION related commands Signal Format INTEGRATOR-SCREEN related commands INTEGRATOR-PICTURE related commandsINTEGRATOR-SETUP related commands INTEGRATOR-OPTION related commands Screen Mask 199 Other commands PIP fade in function effective 201 Quest Commands Quest Command Table Data Content Obtaining QST Status Information Data Content Size Remarks QPI Obtaining Integrator/PICTURE informationQWB Obtaining integrator/WHITE Balance information QPS Obtaining integrator/SCREEN information QSS Obtaining Setup information QSO Obtaining menu integrator/OPTION information Main screen input function Main screen size QCI Obtaining time information QSU obtaining the audio statusQAP Obtaining machine name Table of commands not compatible with PDP-505CMX COF Example 1 When the data is missing 1 Byte Example 2 When 1 Byte of data in the data is unreadableCheck Sum Examples of check sum applications Screen Burning To enjoy using your plasma display for many years Standard Functions Settings cannot be changedSetting example Setting with Menu Mode Setting with Integrator Mode Concerning frame delay lip sync Video input signal Input vertical Frame delayThese data are reference values they cannot be ensured Number Error Message Remedy PrecautionsSelf-diagnosis Function Cabinet and Remote-control Unit Connection procedureDisconnect and Remove Hardware Maintenance Readjustment of the White BalanceScreen front protection panel Vents