Step 1: Set the Edit Points

The first step to editing audio on the VS-1824 is finding the START and END edit points. These edit points indicate where on the track you want to start the edit, and where on the track you want to end the edit. There are many different ways to do this, and many different tools available to help you, including locators, Preview and Scrub.

Here are some common ways to set edit points:

Create locators while the song is playing

Use [FF] and [REW] to locate to point you want to edit

Preview To and Preview From

Scrub

Typically, you will use a combination of the above methods to define edit points.

For example, as you’re listening to your song, you may press a LOCATOR button to establish a point close to where an edit needs to occur. Now that you’re in the ballpark, you might use Preview and Scrub to define a precise edit point.

Quick Editing

Setting Edit Points Using LOCATORS

One of the fastest ways to set edit points is to set locators “on the fly,” that is, while your song is playing. Start by clearing the first two locators (if necessary).

1.Hold [CLEAR] and press [LOCATOR 1]. Hold [CLEAR] and press [LOCATOR 2].

2.Press [PLAY].

3.Press [LOCATOR 1] at the spot where you would like to start an edit.

4.Press [LOCATOR 2] at the end of the section you wish to edit.

LOCATOR Editing Example: Track Erase

Below is a specific example of how to perform one of the most basic edits on the VS-1824, Track Erase. In Track Erase, the area of audio between the Start and End points is replaced with silence. Study the basic steps involved in track editing using this example: editing Track 5.

Before entering Track Edit mode, set your locators.

1.Hold [CLEAR] and press [LOCATOR 1]. Hold [CLEAR] and press [LOCATOR 2].

2.Locate the point in the song where you want to start erasing. Press [LOCATOR 1].

Chapter 11 Editing Tips & Tools

3.Locate the point in the song where you want to end your erasing. Press [LOCATOR 2].

Now try the edit:

1.Hold [SHIFT] and press [F2 (TRACK)].

2.Press [F2 (Erase)] for Track Erase. If you don’t see “Erase” above [F2], press [PAGE] until “Erase” appears, and then press [F2 (Erase)].

3.Press the Track 5 STATUS button to select Track 5 for erasure. The STATUS button turns red, indicating it is the track to be edited. You can press more than one STATUS button if you wish to erase more than one track. To deselect a track, press the STATUS button again to change it back to flashing green.

SPECIAL SHORTCUT: The first four LOCATOR buttons can be used to enter the current time location into the START, END, FROM and TO fields by holding [SHIFT] and the respective LOCATOR button. See Steps 4 through 7 below:

4.Press [LOCATOR 1]. This moves the timeline to the point where you want to begin erasing.

5.Hold [SHIFT] and press [LOCATOR 1]. This enters the current time value (recalled by LOCATOR 1) as the “START” point for the edit.

6.Press [LOCATOR 2]. This moves the timeline to the point where you want to stop erasing.

7.Hold [SHIFT] and press [LOCATOR 2]. This enters the current time value (recalled by LOCATOR 2) as the “END” point for the edit.

8.Press [F4 (Exec)] to execute the edit based on the parameters you’ve defined. If it didn’t work, press [UNDO] and then [ENTER] to “undo” the edit.

Precision Editing

In the previous example, we used locators to set edit points. This is a fast and easy way to perform most edits. For some edits, you may need to define edit points with more precision. To precisely position your edit points, you will need to become familiar with the following tools: The PREVIEW section, Scrub function, and the Waveform display.

Chapter 11

165

Page 165
Image 165
Roland VS-1824 owner manual Set the Edit Points, Quick Editing, Editing Tips & Tools, Precision Editing, 165