Precaution, Location | Sanyo DSR-3009P specification

PRECAUTION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR OTHER MOISTURE. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

If the power supply cord (AC power cord) of this appliance is damaged, it must be replaced. Return to a SANYO Authorised Service Centre for replacement of the cord.

Location

For safe operation and satisfactory performance of your unit, keep the following in mind when selecting a place for its installation:

Shield it from direct sunlight and keep it away from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.

Install the unit in a horizontal position only. Avoid locations subject to strong vibrations.

Avoid moving the unit between cold and hot locations.

Do not place the unit directly on top of a monitor TV, as this may cause playback or recording problems.

Avoiding Electrical Shock and Fire

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.

If any liquid is spilled on the unit, unplug the power cord immediately and have the unit inspected at a factory-authorised service centre.

Do not place anything directly on top of this unit.

SERVICE

This unit is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

Discard used batteries according to the manufacture’s instructions.

English

1

Image 2

Sanyo DSR-3009P instruction manual Precaution, Location, Avoiding Electrical Shock and Fire

Contents

Français F English GBDeutsch D Español E Avoiding Electrical Shock and Fire PrecautionLocation Contents Main Features Setting-up environment Hard disk protection AccessoriesPower cord Fixer power cord tie Ferrite core x Hard disk and cooling fan are consumables Part Names Front panel Part Names Rear panel Connections Connecting high image quality S-VHS video equipmentConnecting to an Amplifier Basic connections DSR-3016P model Digital series connections When using the RS485 RJ-11 connectorConnections System control connections Connecting a remote control circuit External alarm sensor setupUsing as a monitor board during a motion sensor alarm Sensor Alarm OUT connector BUILT-IN Hard Disk Hard disk Basic Normal Enhanced Fine Super Fine BUILT-IN Hard DiskRecording Time Operating display Viewing Camera Images Setting the camera image to single-screen displayPausing images Viewing a single-screen image Press camera select button 2 once more Viewing Camera ImagesPress camera select button Viewing images as a 4-screen display Viewing multiple-screen imagesViewing images as 9-screen or 16-screen displays Plus screen viewing Example To display images from camera 2 in the plus screen Viewing automatically switching imagesAutomatically switching of the single-screen images Automatically switching of the 4-screen images Automatically switching of the plus screen image Canceling monitor 2 display Using two monitors for monitoringDisplaying single-screen alarm images on monitor Operating monitor Recording Images Normal Recording Area Normal recording Timer recording stops when the set end time is reached Timer recordingSet the timer Press the Timer button Set alarm recording Recording Images in the Alarm Recording AreaAlarm recording Suspicious person detection Set pre-alarm recording Recording Images in the Alarm Recording AreaPre-alarm recording Normal playback Playing Back Recorded ImagesPlayback operations Fast forward/fast rewind and reverse playback Playing Back Recorded ImagesPlayback in a single screen Frame advance forward/reverse Zooming the image during playbackViewing still images Playing back images as a 4-screen display Playing back multiple-screen displaysPlaying back images as 9-screen or 16-screen displays Archive area Alarm search SeeSearching for Recorded Images Preview display Searching for Recorded Images Alarm searchPress an Alarm button during playback Turn the shuttle dial clockwise Alarm number of the currently-selected alarm image flashes Alarm thumbnail searchLast nine alarm recording images recorded appear Time/date search Archive area search Example To search for 8 pm on 26 October Motion Detection Search screen appears Alarm display flashesMotion detection search Cursor moves to Start Preview Cursor moves to ChannelExamples of recording area selection 10Use the jog dial to move the cursor to Preview Saving Copying Recorded Images Copy screen appears Saving Copying Recorded ImagesCopying images to the hard disk archive area Archive Area display flashes Cursor moves to Pictures Shuttle dial clockwise CompactFlash recording areaFormatting CompactFlash cards Sanyo IMG00001 IMG00002 IMG00003 Inserting an Scsi card sold separately Connecting to a drive Backing up to a DDS DAT driveInstalledRemoved Model No. Super Store dat 24e Listing Data Press Copy to Abort Copying images to a CD-R drive Menu Flow Chart and Menu Operations Menu Flow Chart Operations while a sub-menu screen is displayed Menu Flow Chart and Menu OperationsBasic menu screen operations Entering numbers LANGUAGE/CLOCK SET menu Setting the languageInitial SET Menu Initial SET Menu Clock SET settingsSetting summer time EXT. Clock SET setting Timer settings To detect an alarm input in a camera image Operable functions during the period set By the timerTo change camera images into automatic switching screens To hide camera images with a gray pattern Holiday SET setting Example To set 17 November as a holiday Automatic camera detection Initial SET sub-menu appears, and the cursor moves to Recording Setting Recording Area SET menu Recording SettingResetting each recording area Total Capacity display Alarm Recording Area Area Full Reset settingFollow the same procedure to make the setting for Recording Conditions SET menu Cursor moves to Overwrite Follow the same procedure to make the setting OFF forCursor moves to Total Number On flashes Relationship between Recording Area SET Normal REC Mode SET menuNormal REC Mode SET setting 1P-1 Repeat the above procedure to set cameras 5 to 16 to OFFProgram REC SET menu Select Individual Camera Rate FPS Timer SET menu Timer SET setting OFF flashes in the SET column Timer reservations spanning more than 24 hoursFlashes in the FPS column Cursor moves to MON 12Press the EXIT/OSD button OFF setting for Program flashesCursor moves to the first line Selects the recording method for alarm images Alarm REC Mode SET menuAlarm REC Mode SET setting = 30721 Alarms can be Recorded = 20480 Alarms can be Recorded = 30200 Alarms can be RecordedDisplay example Alarm recording settings Camera 2 alarm canceled Alarm images Alarm images are recorded Canceled AlternatelyAlarm canceled When 2 or more alarms occur Camera 4 alarm Cursor moves to Alarm Trigger Pre-alarm recording settingCursor moves to the 2SEC setting for Duration and flashes OFF flashes Alarm trigger setting Display examples Alarm recording trigger settings Using the timer function for recording Set the alarm duration for each camera Signal loss detection alarm External alarm detectionDisplayed and SA sensor alarm will Sensor built into this unit an intruder Cursor moves to MON.2 Display Alarm display settingsCursor moves to Alarm Priority Cursor moves to Retrigger Motion Sensor setting Exit 11Press the EXIT/OSD button Setting the alarm durationSetting is then complete Alarm images will appear in a single-screen display Resetting an alarmAlarm will then be canceled Seconds General Setting Title setting General SettingDisplay SET setting Display SET menu Buzzer SET setting Video Loss SET settingColor level settings Auto will flash Operating privileges and security lock Security Lock SET settingSet User password Carried out. When the Administrator password All operations are locked. When the userPassword is entered at the password entry Administrator password is entered, all Canceling the security lock RS-232C/RS-485 SET settingSecurity lock setting RS-232C Selection RS-485 Selection HDD SET settingThis completes the setting and the cursor moves to Control Hard disk initialization Inserting the recommended LAN card Adding a hard diskNetwork connection Cursor moves to Network Control Network SET settingNetwork SET sub-menu appears, and the cursor moves to Cursor moves to IP Address Computer operation Password SET settingExample Set AB123456 as the ID1 password Screen Setting Main menu Repeat steps 4 and 5 above to set 11 and 16 to Screen SettingMulti Screen setting Display examples Press the EXIT/OSD button Changes to 16 and 16 changes to Sequence settingNormal flashes 1S flashes English Sequence SET sub-menu appears 1S flashesCursor moves to Sequence SET Individual Interval SET sub-menu appears Set both Timer a and Timer B Cursor moves to Main Monitor SET 00 12 12 00 16 16 00 24 24 00 6 Mask settings15Press the EXIT/OSD button Example of mask display when timer is set Cursor moves to Mask SET Power FAILURE/USED Time Display About the sub-menu Load menu settings from CompactFlash card Saving Menu Setting DetailsSave menu settings onto a CompactFlash card Saving to a CompactFlash card If copying the recording area settings Saving Menu Setting DetailsLoading saved menu settings Without PRE Alarm With PRE Alarm Interface Specifications Interface Specifications Command Table Specifications Dimensions mm