Power FAILURE/USED Time Display | Sanyo DSR-3009P specs

POWER FAILURE/USED TIME DISPLAY

Main menu

<MAIN MENU>
1.INITIAL SET	->
2.RECORD SET	->
3.GENERAL SET	->
4.SCREEN SET	->
5.POWER FAILURE/USED TIME	->
6.COPY MENU SETTINGS	->

MOVE LINES WITH JOG, SELECT WITH SHUTTLE

1 Press the MENU button to select POWER FAILURE/USED TIME, and then turn the shuttle dial clockwise.

The POWER FAILURE/USED TIME sub-menu appears.

Check details such as the date and time of the power failure and the usage time for the hard disk.

MENU	<POWER FAILURE/USED TIME>
	POWER FAILURE
	#004	FAILURE	02-12	07:22
		RECOVER	02-15	10:20
	USED TIME	DISK1 USE	:	00003H
		DISK1 USE	:	00003H
		DISK2 USE	:	-----H
		POWER	:	00358H
	FIRMWARE :	MAIN 1.10-00 /		SUB 1.01-00

2 Press the EXIT/OSD button.

The display returns to the normal screen.

Sub-menu

<POWER FAILURE/USED TIME> POWER FAILURE

#001 FAILURE 02-12 07:22 1

RECOVER 02-15 10:20 2

USED TIME
DISK1 USE	:	00003H			3

DISK2 USE	:	-----H				4

POWER	:	00358H			5

FIRMWARE : MAIN 1.10-00	/	SUB	1.01-00

About the sub-menu

1FAILURE

Shows the date/time when a power failure occurred.

The number of power failures appears at the left. (example: #020) When the number exceeds 999 it returns to 000.

2RECOVER

Shows the date/time when power was restored.

3DISK1 USE

Shows the total hard disk 1 usage time.

4DISK2 USE

Shows the total hard disk 2 usage time (when a hard disk has been added).

5POWER

Shows the total usage time for this unit.

EXIT/OSD

English

87

Image 88

Sanyo DSR-3009P instruction manual Power FAILURE/USED Time Display, About the sub-menu

Contents

English GB Deutsch DFrançais F Español E Location PrecautionAvoiding Electrical Shock and Fire Contents Main Features Setting-up environment Accessories Power cord Fixer power cord tie Ferrite core xHard disk protection Hard disk and cooling fan are consumables Part Names Front panel Part Names Rear panel Connecting high image quality S-VHS video equipment Connecting to an AmplifierConnections Basic connections DSR-3016P model When using the RS485 RJ-11 connector ConnectionsDigital series connections System control connections External alarm sensor setup Using as a monitor board during a motion sensor alarmConnecting a remote control circuit Sensor Alarm OUT connector BUILT-IN Hard Disk Hard disk Recording Time BUILT-IN Hard DiskBasic Normal Enhanced Fine Super Fine Operating display Setting the camera image to single-screen display Pausing imagesViewing Camera Images Viewing a single-screen image Press camera select button Viewing Camera ImagesPress camera select button 2 once more Viewing multiple-screen images Viewing images as 9-screen or 16-screen displaysViewing images as a 4-screen display Plus screen viewing Automatically switching of the single-screen images Viewing automatically switching imagesExample To display images from camera 2 in the plus screen Automatically switching of the 4-screen images Automatically switching of the plus screen image Using two monitors for monitoring Displaying single-screen alarm images on monitorCanceling monitor 2 display Operating monitor Recording Images Normal Recording Area Normal recording Timer recording Set the timerTimer recording stops when the set end time is reached Press the Timer button Recording Images in the Alarm Recording Area Alarm recordingSet alarm recording Suspicious person detection Pre-alarm recording Recording Images in the Alarm Recording AreaSet pre-alarm recording Playback operations Playing Back Recorded ImagesNormal playback Playback in a single screen Playing Back Recorded ImagesFast forward/fast rewind and reverse playback Viewing still images Zooming the image during playbackFrame advance forward/reverse Playing back images as 9-screen or 16-screen displays Playing back multiple-screen displaysPlaying back images as a 4-screen display Alarm search See Searching for Recorded ImagesArchive area Preview display Alarm search Press an Alarm button during playbackSearching for Recorded Images Turn the shuttle dial clockwise Alarm thumbnail search Last nine alarm recording images recorded appearAlarm number of the currently-selected alarm image flashes Time/date search Archive area search Example To search for 8 pm on 26 October Motion detection search Alarm display flashesMotion Detection Search screen appears Examples of recording area selection Cursor moves to ChannelCursor moves to Start Preview 10Use the jog dial to move the cursor to Preview Saving Copying Recorded Images Saving Copying Recorded Images Copying images to the hard disk archive areaCopy screen appears Archive Area display flashes Cursor moves to Pictures CompactFlash recording area Formatting CompactFlash cardsShuttle dial clockwise Sanyo IMG00001 IMG00002 IMG00003 Connecting to a drive Backing up to a DDS DAT drive InstalledRemovedInserting an Scsi card sold separately Model No. Super Store dat 24e Listing Data Press Copy to Abort Copying images to a CD-R drive Menu Flow Chart and Menu Operations Menu Flow Chart Menu Flow Chart and Menu Operations Basic menu screen operationsOperations while a sub-menu screen is displayed Entering numbers Initial SET Menu Setting the languageLANGUAGE/CLOCK SET menu Setting summer time Clock SET settingsInitial SET Menu EXT. Clock SET setting Timer settings Operable functions during the period set By the timer To change camera images into automatic switching screensTo detect an alarm input in a camera image To hide camera images with a gray pattern Holiday SET setting Example To set 17 November as a holiday Automatic camera detection Initial SET sub-menu appears, and the cursor moves to Recording Setting Recording Setting Resetting each recording areaRecording Area SET menu Total Capacity display Area Full Reset setting Follow the same procedure to make the setting forAlarm Recording Area Recording Conditions SET menu Follow the same procedure to make the setting OFF for Cursor moves to Total NumberCursor moves to Overwrite On flashes Normal REC Mode SET setting Normal REC Mode SET menuRelationship between Recording Area SET Repeat the above procedure to set cameras 5 to 16 to OFF Program REC SET menu1P-1 Select Individual Camera Rate FPS Timer SET menu Timer SET setting Timer reservations spanning more than 24 hours Flashes in the FPS columnOFF flashes in the SET column Cursor moves to MON Cursor moves to the first line OFF setting for Program flashes12Press the EXIT/OSD button Alarm REC Mode SET menu Alarm REC Mode SET settingSelects the recording method for alarm images = 30721 Alarms can be Recorded Display example Alarm recording settings = 30200 Alarms can be Recorded= 20480 Alarms can be Recorded Alarm images Alarm images are recorded Canceled Alternately Alarm canceledCamera 2 alarm canceled When 2 or more alarms occur Camera 4 alarm Pre-alarm recording setting Cursor moves to the 2SEC setting for Duration and flashesCursor moves to Alarm Trigger OFF flashes Alarm trigger setting Display examples Alarm recording trigger settings Using the timer function for recording Set the alarm duration for each camera External alarm detection Displayed and SA sensor alarm willSignal loss detection alarm Sensor built into this unit an intruder Alarm display settings Cursor moves to Alarm PriorityCursor moves to MON.2 Display Cursor moves to Retrigger Motion Sensor setting Exit Setting is then complete Setting the alarm duration11Press the EXIT/OSD button Resetting an alarm Alarm will then be canceledAlarm images will appear in a single-screen display Seconds General Setting General Setting Display SET settingTitle setting Display SET menu Video Loss SET setting Color level settingsBuzzer SET setting Auto will flash Set User password Security Lock SET settingOperating privileges and security lock All operations are locked. When the user Password is entered at the password entryCarried out. When the Administrator password Administrator password is entered, all RS-232C/RS-485 SET setting Security lock settingCanceling the security lock RS-232C Selection HDD SET setting This completes the setting and the cursor moves to ControlRS-485 Selection Hard disk initialization Network connection Adding a hard diskInserting the recommended LAN card Network SET setting Network SET sub-menu appears, and the cursor moves toCursor moves to Network Control Cursor moves to IP Address Example Set AB123456 as the ID1 password Password SET settingComputer operation Screen Setting Main menu Screen Setting Multi Screen settingRepeat steps 4 and 5 above to set 11 and 16 to Display examples Press the EXIT/OSD button Sequence setting Normal flashesChanges to 16 and 16 changes to 1S flashes English 1S flashes Cursor moves to Sequence SETSequence SET sub-menu appears Individual Interval SET sub-menu appears Set both Timer a and Timer B Cursor moves to Main Monitor SET 15Press the EXIT/OSD button Mask settings00 12 12 00 16 16 00 24 24 00 6 Example of mask display when timer is set Cursor moves to Mask SET Power FAILURE/USED Time Display About the sub-menu Saving Menu Setting Details Save menu settings onto a CompactFlash cardLoad menu settings from CompactFlash card Saving to a CompactFlash card Loading saved menu settings Saving Menu Setting DetailsIf copying the recording area settings Without PRE Alarm With PRE Alarm Interface Specifications Interface Specifications Command Table Specifications Dimensions mm