Using the Touch Panel, How to use the touch panel | Sharp AR-507

CHAPTER1

USING THE TOUCH PANEL

How to use the touch panel

GETTING STARTED Using the touch panel

READY TO COPY.

1.A4

2.A3

AUTO	1	11	100%
	AUTO 8/2
EXPOSURE	PAPER SELECT		COPY RATIO

You can set or cancel a function displayed on the touch panel by pressing (touching) a key with a finger. The touch key operation can be confirmed with a beep tone (and highlighted display).

★KEY OPERATOR For the beep tone to be heard, the beep tone must be enabled by a key operator program. See page 8-29.

If any keys are displayed gray, the keys have been disabled. If you press these keys, two short beeps will be sounded.

RECALL STORE/DELETE

Selection of function

			OK
ERASE		CANCEL	OK
EDGE ERASE			10 mm(0~20)
EDGE ERASE
CENTRE ERASE
EDGE+CENTRE
ERASE
READY TO COPY.
SPECIAL MODES			OK
MARGIN SHIFT	ERASE		DUAL PAGE
MARGIN SHIFT	ERASE		COPY
			COPY
MULTI SHOT	COVERS	TRANSPARENCY
MULTI SHOT	COVERS		INSERTS
			INSERTS
PAMPHLET COPY	IMAGE EDIT		TEXT STAMP
AUTO	AUTO A4		100%
EXPOSURE	PAPER SELECT		COPY RATIO

To register the selected settings for a function, press the “OK” key on the setting screen. The settings indicated by a highlighted display will be registered as a selected function.

Some special functions can be selected by pressing the relevant keys on the SPECIAL MODES screen (page 3-4) or on the IMAGE EDIT menu (page 3-21) to highlight the keys. To cancel these functions, press the relevant keys again to return the keys to the normal display. These functions are: Dual page copying, Centring, B/W reverse, and Binding change.

1-8

Image 12

Sharp AR-507 operation manual Using the Touch Panel, How to use the touch panel, Selection of function

Contents

AR-507 CINSE1982FC51 Contents Using this Manual IntroductionFor General Users For Key Operators Chapter Installation Requirements Getting Started Cautions Class Laser Product Laser Klasse Power on and OFF Power on and OFF Power save modesAuto power shut-off mode Preheat mode Press the Information key in the standby mode Information Function Using the Touch Panel How to use the touch panelSelection of function Function setting icons Using the Touch PanelParticular settings for these functions Can be easily called by pressing its icon Face UP/FACE Down Delivery Making Copies Special Papers manual feed Auditing Accounts Enter Your Account Number Using the Rspf Stream feeding modeDifferent copy image ranges Using the Rspf Sided copies of 1-sided originalsUse the 10-key pad to enter the desired number Copies Press the Start key Sided copies from 1-sided originals Press the 2-SIDED Copy keyPress the key on the touch panel Sided copies from 2-sided originals To cancel a copy run, press the Clear ALL CA key. Copying Close the document feeder cover Making Copies Copying from Copying from the Document Glass Replace the first original with the next original after Key indicator lights up, Remove the first original and replace it with the next REDUCTION/ENLARGEMENT/ZOOM Automatic selection REDUCTION/ENLARGEMENT/ZOOM Manual selection 141 % Special Papers manual feed Insert the copy paper all the way into the bypass tray Special Papers manual feed Two-sided copying with bypass tray Exposure Adjustments AutomaticText, text/photo, and photo Sort mode Group modeSORT/GROUP All copies of the same original will be grouped in the exit JOB Memory Storing a job programPress the Program P key Press the STORE/DELETE key on the touch panel JOB Memory Deleting a stored job programRecalling a job program Interrupting a Copy RUN Press the Interrupt key Special Functions XY Zoom Press the XY Zoom key XY Zoom Press the Y keyUse the reduction, enlargement, and Zoom Keys to change the copy ratio in the vertical Y direction Margin Shift Special Modes screen will appear Select the desired shift amounts using the and 5 keys Margin ShiftPress the Margin Shift key on the touch panel Select the shift direction Erase Press the Erase key on the touch panel Select the desired erase mode Adjust the amount of edge erase and/or centre erase ifErase Needed Dual page Copying Place the originals on the document glass withPress the Dual page Copy key on the touch panel Dual page Copying Ensure that the desired tray is selectedEnter the desired number of copies Multi Shot Multi Shot Press the upper OK key Covers Place the originals in the document feeder trayPress the 2-SIDED Copy key and select the desired Duplex selection window Select cover placement CoversPress the upper OK key Enter the desired number of copies and press the Start key Transparency Film with Insert Sheets Press the Transparency Inserts key on the touch panel Transparency Film with Insert Sheets Ensure that the desired tray is selected for insert sheets Pamphlet Copy Place the originals in the document feeder tray or on Pamphlet Copy Press the Pamphlet Copy key on the touch panelSelect the type of originals Select the binding position AUT Check the copy paper selection Image Editing Functions JOB Build Make all other desired copy mode selections and enter Image Editing FunctionsPress the Image Edit key Press the JOB Build key Centring After the first section of original pages has been fed Press the Image Edit key on the touch panel Press the Centring keyPress the Paper Select key on the touch panel Replace the finished original with the next original after On the touch panel Select the desired copy paper size Press the Repeat Copy key on the touch panel Cancel OK Border Line Special Modes screen will appear Image Edit menu will appearPress the B/W Reverse key on the touch panel Centring E F Press the Binding Change key on the touch panel Press the Image Edit key on the touch panel Make all other desired copier selections and enter Text Stamp Date Text Stamp Select the print direction Press the Select Stamp key on the touch panel Adjust the darkness of the background of the stamp Select the stamp positionSelect the desired stamp to be printed Cancel OK Position Draft To adjust the exposure, press the Option key Adjust the darkness of the watermarkPress the Watermark key on the touch panel Select the desired watermark to be printed Cancel OK 11Press the upper OK key Number Press the page Number key on the touch panel Select the desired page number formatSelect the starting page number OK 9 Press the upper OK key Replace the finished original with the next original after Tandem Copy Press the Tandem Copy key on the touch panel Copier is installed in the sub copier Tandem CopyOn the main copier, press the Start key Setting Review Press the Review keyExample To exit the review screen, press the Exit key Supplies Paper Types and sizes of copy paperLoading copy paper Paper Loading paper in paper trays 1Push the paper tray firmly back into the copier Changing the copy paper size in the tray Load copy paper into the tray Adding Toner Open the front coverNew toner cartridge vertically and vigorously shake it Up and down about 20 times, then invert the cartridge Adding Toner Add only one cartridge of toner Used Toner Disposal Disengage and remove the container from the copierPlace Close the toner collecting container cover Open the toner collecting container cover Storage of Supplies Photoconductive drumProper storage Store the supplies in a location that is Copier TROUBLE? Misfeed Removal Misfeed in the Rspf Misfeed Removal Open the feeding roller coverRemove the misfed original. Close the paper guide after Removing the misfed original Transport cover COPIERTROUBLE? Misfeed removal Misfeed in the bypass tray Misfeed in paper trays 1Open the right side cover Hold the handle and gently open the cover Misfeed in the transport area Remove the misfed paper Transport lever Roller rotating knob a Paper guide Misfeed around the fusing unit and exit area Open the exit area cover carefully Remove the misfed paper Close the exit area cover Close the front cover Misfeed in the reversing area Open the left side cover Gently remove the misfed paper Misfeed in the duplex module Close the exit area cover and the left side coverOpen the exit area cover carefully Close the exit area cover Maintenance Required Troubleshooting Troubleshooting Self-diagnostic functionPage General Information Part Names and Functions Exterior Part Names and Functions Interior Operation Panel Touch Panel Basic screen User Maintenance Document glass and document feeder coverRspf scanning section Touch Panel Contrast Adjustment Press the Custom Settings key Specifications Copier Specifications Document FeederPage Optional Equipment System Configuration Specifications Finisher AR-FN3Part Names Offset mode NON-OFFSET modeFinisher AR-FN3 Offset stack Staple Sort mode Sort and group Using the Rspf Staple sortSet the originals in the document feeder tray Press the Output key Staple Sort Sort Group Select the desired stapling position Using the document glass To be stapled to the upper right Key on the touch panel Press the OK key Staple cartridge replacement Remove the rear paper and tape from the cartridge 11Push the finisher toward the copier and latch it in place Staple jam removal Return the lever to its original position Insert the staple box into the stapler unit until it clicks10Push the finisher toward the copier and latch it in place Misfeed removal Misfeed in the upper transport area Close the top cover Cover of the paper feed area and open the top cover Misfeed in the lower transport area Push the finisher toward the copier and latch it in place Removing the paper Close the paper transport area cover Specifications Large Capacity Tray AR-LC1N Large capacity tray AR-LC1N Chapter Large Capacity Tray AR-LC1N Remove the misfed paper Gently push the tray back into place STAND/500-SHEET Paper Drawer AR-DE7 STAND/500-SHEET Paper Drawer AR-DE7 Open the lower right side cover and remove any misfed paper Page KEY OPERATOR’S Guide Enter your key operator code number using the 10-key Pad KEY Operator Code NumberRegistering the key operator code number KEY Operator Code Number Press the KEY Operator Code Number Change Key KEY Operator Programs KEY Operator Programs Extra KEY Operator Programs Using the key operator programs Enter the key operator code numberPress the Copier key on the touch panel Dashes in the display will change to asterisks Select the desired category on the touch panel Press the key of the desired program on the touch panelFollow instructions for the program Auditing Mode Number of Copies per AccountPress the key to advance through the accounts Billing by Account Press the OK key to exit the program Resetting Account To reset all accountsTo reset a single account Press the key of an account to be reset Account Number Control To register accountsTo delete accounts Press the Enter key Price/Copy Setting To change an account numberTo print all registered account numbers Press the Print key Account Limit Setting To set a limitEnter the price code #1 #3 and then press the Enter key Continue with steps 3 and 4 for other individual accounts To set a limit for all accounts Account Number Security Exposure Adjustment Adjust the exposure using the and keys Press the OK keyKey Operator Code Number Change Add or Change Extra Preset Ratios Setting a Maximum Number of CopiesInput the number using the 10-key pad Use the and keys to set the desired copy ratio Initial Margin Shift Setting Erase Width AdjustmentAdjust the value for each side using the and keys Initial Status Setting To establish new initial settingsTo return to the factory default settings Stream Feeding Mode Staple Position Setting Date Format Setting Date and Time Adjustment Rotation Copy Setting Size Setting for Extra Heavy Paper on the Bypass Tray Auto Power Shut-off Timer Auto Clear SettingEnter the time interval using the and keys Press the OK key Set the desired time interval using the and keys Preheat Mode Setting Noise Level Reduce ModeSet the time using the and keys Message Time Setting Set the time using the and keys Press the OK key Disabling of Auto Tray Switching Disabling of Auto Paper SelectionDisabling of Bypass-Tray in Duplex Copy Disabling Deletion of Job Programs Disabling of Document FeederDisabling of Duplex Copying Disabling of Covers Mode Disabling of PC/Modem AccessDisabling of Stapler Prohibit Auto Paper Selection from the Bypass-Tray Disabling of Auto Power Shut-off Mode Disabling of Beep When Keys Touched Total Count Program List PrintoutPress the Program List PRINTOUT. key Finisher is OUT of SERVICE. Press CA to Cancel JOB KEY Operator Assistance Call Memo KEY Operator Code Number Factory Setting Factory setting = 2000C DSC1 CINSE1982FC51 Mains Plug Wiring Instructions Sharp Corporation