Manuals / Sharp / Computer Equipment / Copier

Sharp AR-507 7-25, STAND/500-SHEET PAPER DRAWER AR-DE7, Misfeed removal, A Misfeed Has Occurred

Models: AR-507

1 176

Download 176 pages 39.59 Kb

Page 139

Image 139

Open the lower right side cover and remove any misfed paper.

STAND/500-SHEET PAPER DRAWER (AR-DE7)

Misfeed removal

A MISFEED HAS OCCURRED.

The copier will stop when a misfeed occurs.

The message “A MISFEED HAS OCCURRED. CLEAR INDICATED

AREA. PRESS FOR RECOVERY INSTRUCTIONS.” will appear with a display of paper misfeed locations. Press the INFORMATION () key for more detailed information as necessary.

CLEAR	INDICATED AREA.
PRESS	FOR RECOVERY INSTRUCTIONS.

Open the lower right side cover and remove any misfed paper.

●Be sure to perform this step before pulling out the paper drawer. If not, the paper may be torn as the drawer is opened.

●Be sure not to tear the misfed paper during removal.

Gently lift and pull out the paper drawer. Remove any misfed paper.

OPTIONAL EQUIPMENT

Stand/500-sheet paper drawer (AR-DE7)

Close the paper drawer and the lower right side cover.

Open and close the front cover to cancel the misfeed display.

●Confirm that the misfeed display is cleared.

CHAPTER7

7-25

Page 139

Image 139

Sharp AR-507 7-25, STAND/500-SHEET PAPER DRAWER AR-DE7, Misfeed removal, A Misfeed Has Occurred, Indicated Area, Clear

Contents

AR-507 For a complete electrical disconnection, pull out the main plug CHAPTER SPECIAL FUNCTIONS CONTENTSCHAPTER GETTING STARTED CHAPTER MAKING COPIESFor Key Operators USING THIS MANUALINTRODUCTION For General UsersPOWER ON AND OFF CHAPTERGETTING STARTED INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS Cautions on laser CAUTIONSVORSICHT CAUTIONSCLASS LASER PRODUCT LASER KLASSE VAROITUSPower onup takes less than 150 seconds. Once the copier is ready, the POWER ON AND OFFCHAPTER1 GETTING STARTED Power on and off Preheat mode POWER ON AND OFFPower save modes Auto power shut-off modeCHAPTER1 INFORMATION FUNCTION~200g/m2 Press the INFORMATION key in the standby modeHow to use the touch panel USING THE TOUCH PANELSelection of function the basic screen. The setting screen for a selected function Function setting iconsUSING THE TOUCH PANEL particular settings for these functions1-10 FACE UP/FACE DOWN DELIVERYCHAPTER1 CHAPTER MAKING COPIESUSING THE RSPF EXPOSURE ADJUSTMENTSKEY OPERATOR AUDITING ACCOUNTSSee page 8-14 for account limit settings manual for the printer auditing mode settingStream feeding mode USING THE RSPF2. Different copy image ranges 1-sided copies of 1-sided originals USING THE RSPFAdjust the original guides to the size of the originals and Ensure that the 1-sided to 1-sided copying mode is2-sided copies from 1-sided originals AUTOUSING THE RSPF Adjust the original guides to the size of the originals andPress the 2-SIDED COPY key Press the key on the touch panel USING THE RSPFUsing the RSPF 2-sided copies from 2-sided originals1 set the originals face up in the document feeder tray USING THE RSPFAdjust the original guides to the size of the originals and 1-sided copies from 2-sided originalsOpen the document feeder cover and place an original COPYING FROM THE DOCUMENT GLASSEnsure that the 1-sided to 1-sided copying mode is 1-sided copies of 1-sided originalsUse the 10-key pad to enter the desired number of 4 copies 1 glass, using the centring scale to position itCOPYING FROM THE DOCUMENT GLASS 2-sided copies from 1-sided originals3 Press the 2-SIDED COPY key 4 Press the key on the touch panel 2-10key indicator lights up, and COPYING FROM THE DOCUMENT GLASS100% REDUCTION/ENLARGEMENT/ZOOM2-11 Automatic selectionA. Preset reduction copy ratios are 50% and 25% 95%, 50%, and 25% 2-12100 % A. Preset reduction copy ratios are 86%, 81%, and 70% 77% and 64%5 Press the “OK” key 2-13141 % REDUCTION/ENLARGEMENT/ZOOM1 document glass 2 Open the bypass tray SPECIAL PAPERS manual feed2-14 Place the original in the document feeder tray or on the5 then select the bypass tray 2-15SPECIAL PAPERS manual feed Two-sided copying with bypass trayPhoto mode EXPOSURE ADJUSTMENTS2-16 Text modeGROUP mode SORT/GROUP2-17 SORT mode1 Press the PROGRAM P key JOB MEMORY2-18 Storing a job programCANCEL DELETE STORE 2-194 Press the “EXIT” key to exit the job memory mode To cancel deletion, press the “CANCEL” keyWhen the interrupt copy run is complete, press the INTERRUPTING A COPY RUN2-20 When the copier stops, remove the originals and setXY ZOOM SPECIAL FUNCTIONSSETTING REVIEW CHAPTERXY ZOOM XY ZOOM100% ELECT141% XY ZOOM50 % 100 %Press the SPECIAL MODES key MARGIN SHIFTPlace the original in the document feeder tray or on the 1 document glassPress the “MARGIN SHIFT” key on the touch panel Select the desired shift amounts using the and 5 keysSIDE MARGIN SHIFT1 document glass ERASEAB A B Place the original in the document feeder tray or on theERASE CANCEL OKSelect the desired erase mode Adjust the amount of edge erase and/or centre erase ifPlace the originals on the document glass with the DUAL PAGE COPYINGDUAL PAGE COPY TRANSPARENCY INSERTSEnsure that the desired tray is selected DUAL PAGE COPYINGPress the START key Replace the finished original with the next original afterAUTO MULTI SHOT3-10 Press the 2-SIDED COPY key and select a duplex modeSelect the number of originals to be included on one 3-11MULTI SHOT Press the “MULTI SHOT” key on the touch panelReplace the finished original with the next original after 3-12MULTI SHOT Press the START key2 duplex mode if needed. Press the “OK” key to close the COVERS3-13 READY TO COT ON FRONT COVER? NCEL3-14 Select cover placementPress the SPECIAL MODES key 3-15TRANSPARENCY FILM WITH INSERT SHEETS READY TO CO6 Load transparency film into the bypass tray 3-16TRANSPARENCY FILM WITH INSERT SHEETS 5 Press the upper “OK” keyPress the SPECIAL MODES key PAMPHLET COPY3-17 1 document glassSelect the type of originals 3-18PAMPHLET COPY Press the “PAMPHLET COPY” key on the touch panelEnter the desired number of copies Press the START key 3-19PAMPHLET COPY Check the copy paper selectionAUTO IMAGE EDITING FUNCTIONS3-20 If a duplex copy mode is required, it must be selected atIMAGE EDITING FUNCTIONS NCEL OK T ON FRONT COVER?3-21 Make all other desired copy mode selections and enterPress the START key 3-22IMAGE EDITING FUNCTIONS CENTRING2 select the desired paper size 3-23IMAGE EDITING FUNCTIONS G REPEAT COPYPress the START key 3-24IMAGE EDITING FUNCTIONS REPEAT COPYPOSURE 3-25IMAGE EDITING FUNCTIONS AUTO8 Press the upper “OK” key 3-26IMAGE EDITING FUNCTIONS Select a type of border lineB/W REVERSE 3-27READY TO CO IMAGE EDITING FUNCTIONSCENTRING 3-28IMAGE EDITING FUNCTIONS OK OKC D E F 3-29BINDING CHANGE IMAGE EDITING FUNCTIONS 3-302 sided copy mode AUTOCENTRING 3-31IMAGE EDITING FUNCTIONS OK OKDATE TEXT STAMP3-32 READY TO COPress the “TEXT STAMP” key on the touch panel CANCEL OK3-33 TEXT STAMPSelect the print direction 3-34TEXT STAMP DATETEXT STAMP 3-35READY TO CO UrgentTEXT STAMP 3-36To adjust the exposure and print position, press the Adjust the darkness of the background of the stampDATE 3-37CANCEL OK POSITION TEXT STAMPWATERMARK 3-38Draft TEXT STAMPTEXT STAMP 3-39To adjust the exposure, press the “OPTION” key Adjust the darkness of the watermarkPress the lower “OK” key 3-40CANCEL OK TEXT STAMPTEXT STAMP 3-41READY TO CO PAGE NUMBERSelect the desired page number format 3-42TEXT STAMP Press the “PAGE NUMBER” key on the touch panelPAGE 3-43TEXT STAMP OK 9 Press the upper “OK” key1 tandem-connection cable and they have been turned on TANDEM COPY3-44 Ensure that the two copiers are connected through theDUAL PAGE COPY TRANSPARENCY INSERTS 3-45Make all other desired copier settings and enter the 7 copier is installed in the sub copierCOPY RATIO SETTING REVIEW3-46 100%Loading copy paper SUPPLIESCHAPTER PAPERTypes and sizes of copy paper PAPERLoading copy paper 1 Gently lift and pull out the paper tray Only use paper within the Sharp specification andPAPER Loading paper in paper trays 1 andChanging the copy paper size in the tray Adjust the paper size indicator to match the paper size 2 to be setAdjust the front guide and left guide while squeezing PAPERPull down the toner hopper lock lever and pull the toner ADDING TONERGENUINE SUPPLIES 1 Open the front coverSlide the empty toner cartridge back along the guides and remove it ADDING TONERSlide the toner cartridge along the guides over the toner hopper Pull on the sealing tape to remove it3 place USED TONER DISPOSALInstall a new toner collecting container until it clicks into Disengage and remove the container from the copierGENUINE SUPPLIES STORAGE OF SUPPLIESPhotoconductive drum Proper storageCHAPTER COPIER TROUBLE?MAINTENANCE REQUIRED TROUBLESHOOTINGAn original misfeed may occur at one of two locations MISFEED REMOVALMisfeed in the RSPF First confirm the misfeed locationsRotate the roller in the direction of the arrow and gently MISFEED REMOVALA Open the feeding roller cover Open the paper guideGently remove the misfed original MISFEED REMOVALOpen the document feeder and gently remove the misfed original B Unlock the lever and open the transport coverMISFEED REMOVAL Open and close the front cover to cancel the misfeed 2 displayFOR RECOVERY INSTRUCTIONS FOR RECOVERY INSTRUCTIONSRemove the misfed paper Open and close the front cover to cancel the misfeed 5 displayMISFEED REMOVAL Misfeed in the transport areaCHAPTER5 MISFEED REMOVAL2 Remove the misfed paper Close the front cover2 Open the exit area cover carefully 3 Remove the misfed paper Misfeed around the fusing unit and exit areaMISFEED REMOVAL 1 Open the front cover4 Close the exit area cover Close the front cover MISFEED REMOVALCHAPTER5 Misfeed in the reversing area 5-10FOR RECOVERY INSTRUCTIONS MISFEED REMOVAL3 Close the exit area cover and the left side cover 5-11MISFEED REMOVAL Misfeed in the duplex module3 Close the exit area cover 5-12Open and close the front cover to cancel the misfeed 4 display MISFEED REMOVAL5-13 MAINTENANCE REQUIREDCHAPTER5 COPIER TROUBLE? Maintenance required 5-14 TROUBLESHOOTINGCHAPTER5 COPIER TROUBLE? Troubleshooting CONFIGURED TO PERFORM 5-15TROUBLESHOOTING Self-diagnostic functionPage SPECIFICATIONS GENERAL INFORMATIONUSER MAINTENANCE TOUCH PANEL CONTRAST ADJUSTMENTCHAPTER6 PART NAMES AND FUNCTIONSPower switch ExteriorTransport lever Fusing unitAccessories PART NAMES AND FUNCTIONS InteriorPART NAMES AND FUNCTIONS Operation Panel INTERRUPT key and indicator pSTART key and indicator Function setting icons p.1-9PART NAMES AND FUNCTIONS Touch Panel Basic screen CUSTOM SETTINGS keyInitial settings Initial settings can beDocument glass and document feeder cover USER MAINTENANCERSPF scanning section Touch panel contrast adjustment TOUCH PANEL CONTRAST ADJUSTMENT1 Press the CUSTOM SETTINGS key Press the “LIGHTER” or “DARKER” key to adjust the contrastCOPIER SPECIFICATIONSCHAPTER6 CHAPTER6 SPECIFICATIONSDOCUMENT FEEDER DUPLEX MODULEPage FINISHER AR-FN3 OPTIONAL EQUIPMENTSYSTEM CONFIGURATION CHAPTERCHAPTER7 SYSTEM CONFIGURATIONSpecifications FINISHER AR-FN3PART NAMES inch from the previous set. When copying in the GROUP OFFSET modeNON-OFFSET mode When copying in the SORT mode, each collated set ofFINISHER AR-FN3 SORT modeGROUP mode STAPLE SORT modeAUTO Using the RSPFFINISHER AR-FN3 Staple sortPress the “OK” key Set the number of copies Press the START key FINISHER AR-FN3STAPLE SORT SORT GROUP Select the desired stapling position2 Press the OUTPUT key Using the document glassFINISHER AR-FN3 STAPLE SORT SORT GROUP7 Press the START key indicator lights up, and then pressFINISHER AR-FN3 6 Set the number of copiesLower the lock lever to unlock the stapler unit 7-10Staple cartridge replacement FINISHER AR-FN39 into place 7-11FINISHER AR-FN3 Insert the staple box into the stapler unit until it clicksLower the lock lever to unlock the stapler unit 7-12FINISHER AR-FN3 Staple jam removal8 place Lower the lock lever and return the stapler unit to face 7-13FINISHER AR-FN3 7 Return the lever to its original positionMisfeed in the upper transport area 7-14FINISHER AR-FN3 Misfeed removal3 the cover of the paper feed area of the finisher 7-15FINISHER AR-FN3 If the misfed paper cannot be removed in step 2, openMisfeed in the lower transport area 7-16FOR RECOVERY INSTRUCTIONS FINISHER AR-FN34 Close the transport 7-17FINISHER AR-FN3 Remove the misfed paperRoller rotating knob 7-18FINISHER AR-FN3 Close the paper transport area coverPART NAMES LARGE CAPACITY TRAY AR-LC1N7-19 SpecificationsLarge capacity tray AR-LC1N CHAPTER OPTIONAL EQUIPMENT7Remove any misfed paper from the copier and the large capacity tray 7-21LARGE CAPACITY TRAY AR-LC1N Misfeed removalRemove the misfed paper Gently push the tray back into place 7-22LARGE CAPACITY TRAY AR-LC1N If misfed paper is not found in step 2, pull the tray outPART NAMES 7-23Specifications STAND/500-SHEET PAPER DRAWER AR-DE7STAND/500-SHEET PAPER DRAWER AR-DE7 7-24Loading copy paper STAND/500-SHEET PAPER DRAWER AR-DE7 7-25Open and close the front cover to cancel the misfeed display FOR RECOVERY INSTRUCTIONSPage KEY OPERATOR CODE NUMBER KEY OPERATOR’S GUIDEFACTORY SETTING CHAPTEREnter your key operator code number using the 10-key 3 pad KEY OPERATOR CODE NUMBER6~200g/m2 1 Press the CUSTOM SETTINGS keyPress the OK key Choose a new 5-digit code number and enter it using the 10-key padKEY OPERATOR CODE NUMBER Press the “KEY OPERATOR CODE NUMBER CHANGE.” 6 keyKEY OPERATOR’S GUIDE8 KEY OPERATOR PROGRAMSKEY OPERATOR PROGRAMS KEY OPERATOR PROGRAMS 6~200g/m2 Using the key operator programs1 Press the CUSTOM SETTINGS key CUSTOM SETTINGSFollow instructions for the program KEY OPERATOR PROGRAMSSelect the desired category on the touch panel Press the key of the desired program on the touch panelNumber of Copies per Account ACCOUNT CONTROLAuditing Mode KEY OPERATOR PROGRAMS1. Press the key to advance through the accounts 8-10KEY OPERATOR PROGRAMS Billing by AccountTo reset a single account 8-11KEY OPERATOR PROGRAMS Resetting Account To reset all accountsTo register accounts 8-122. Enter a 5-digit account number 00001 to 99999 using the 10-key pad KEY OPERATOR PROGRAMS Account Number ControlKEY OPERATOR PROGRAMS 8-13Price/Copy Setting 2. Enter the account number to be changed using the 10-key padTo set a limit 8-14Account Limit Setting KEY OPERATOR PROGRAMSAccount Number Security 8-15KEY OPERATOR PROGRAMS To set a limit for all accounts1. Adjust the exposure using the and keys 2. Press the “OK” key OTHER FUNCTION SETTINGS8-16 Exposure Adjustment1. Input the number using the 10-key pad 8-17KEY OPERATOR PROGRAMS Add or Change Extra Preset Ratios Setting a Maximum Number of Copies1. Adjust the value for each side using the and keys 8-18KEY OPERATOR PROGRAMS Initial Margin Shift Setting Erase Width AdjustmentTo return to the factory default settings 8-19KEY OPERATOR PROGRAMS Initial Status Setting To establish new initial settings1. Select the desired stapling position on the touch panel 8-20KEY OPERATOR PROGRAMS Staple Position Setting Date Format Setting1. Select an item to be adjusted and adjust the value using 8-21KEY OPERATOR PROGRAMS Date and Time Adjustment Rotation Copy SettingHeavy Paper on the Bypass Tray 8-22KEY OPERATOR PROGRAMS Size Setting for EXTRA 2. Select a paper size for EXTRA settingAuto Clear Setting TIMER SETTINGS8-23 Auto Power Shut-off Timer1. Set the desired time interval using the and keys 8-24KEY OPERATOR PROGRAMS Preheat Mode Setting Noise Level Reduce ModeKEY OPERATOR PROGRAMS Message Time Setting 8-251. Set the time using the and keys 2. Press the “OK” key KEY OPERATOR PROGRAMS ENABLE/DISABLE SETTINGS8-26 Disabling of Auto Tray SwitchingDisabling of Duplex Copying 8-27KEY OPERATOR PROGRAMS Disabling Deletion of Job Programs Disabling of Document FeederKEY OPERATOR PROGRAMS Disabling of Stapler 8-28Disabling of Covers Mode Disabling of PC/Modem AccessTo disable the auto power shut-off mode, press the check box of “DISABLING OF AUTO POWER SHUT-OFF MODE.” to display a check mark in the check box 8-29Disabling of Auto Power Shut-off Mode Disabling of Beep When Keys TouchedTotal Count OTHER PROGRAMS8-30 KEY OPERATOR PROGRAMSTHE DOCUMENT FEEDER IS OUT OF SERVICE. PRESS CA TO CANCEL JOB KEY OPERATOR ASSISTANCE CALL8-31 THE FINISHER IS OUT OF SERVICE. PRESS CA TO CANCEL JOB8-32 MEMOKEY OPERATOR Detach this page and store it in a safe place KEY OPERATOR CODE NUMBER FACTORY SETTING8-33 Factory setting =2000C DSC1 CINSE1982FC51 GREEN-AND-YELLOW Earth BLUENeutral BROWNLive MAINS PLUG WIRING INSTRUCTIONSSharp House, Thorp Road, Newton Heath, Manchester M40 5BE SHARP CORPORATIONAR-507 PRINTEDIN JAPAN