Manuals / Sharp / Computer Equipment / Copier

Sharp AR-507 Misfeed Removal, Misfeed in the RSPF, First confirm the misfeed locations

Models: AR-507

1 176

Download 176 pages 39.59 Kb

Page 90

MISFEED REMOVAL

MISFEED REMOVAL

When a misfeed occurs, the copier will stop.

The message “A MISFEED HAS OCCURRED. CLEAR

INDICATED AREA. PRESS FOR RECOVERY INSTRUCTIONS.” will appear with a display of paper misfeed locations. Press the INFORMATION () key for more detailed information as necessary.

If paper becomes accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum or the corona wires.

( P. 5-6)

( P. 5-8) ( P. 5-11)

					( P. 5-10, 5-11)
CHAPTER5
COPIER
COPIER				A MISFEED HAS OCCURRED.
TROUBLE?				CHECK THE INDICATED AREA AND REMOVE
				CHECK THE INDICATED AREA AND REMOVE
				THE MISFEED ORIGINAL.
Misfeed
Misfeed			CLEAR INDICATED AREA.
			CLEAR INDICATED AREA.

removal			PRESS		FOR RECOVERY INSTRUCTIONS.

AB

First confirm the misfeed locations.

For misfeeds in optional equipment, see their respective sections. (pages 7-14, 7-21, and 7-25)

( P. 5-2)

( P. 5-5)

( P. 5-5)

Misfeed in the RSPF

When the RSPF misfeeds an original sheet, the copier will stop and the misfeed message will appear.

The misfeed message display varies with the misfed area.

An original misfeed may occur at one of two locations:

(A) in the RSPF feed section or (B) in the exit section.

5-2

Image 90

Sharp AR-507 operation manual Misfeed Removal, Misfeed in the RSPF, First confirm the misfeed locations

Contents

AR-507 For a complete electrical disconnection, pull out the main plug CHAPTER MAKING COPIES CONTENTSCHAPTER GETTING STARTED CHAPTER SPECIAL FUNCTIONSFor General Users USING THIS MANUALINTRODUCTION For Key OperatorsINSTALLATION REQUIREMENTS CHAPTERGETTING STARTED POWER ON AND OFFINSTALLATION REQUIREMENTS CAUTIONS Cautions on laserVAROITUS CAUTIONSCLASS LASER PRODUCT LASER KLASSE VORSICHTPOWER ON AND OFF Power onup takes less than 150 seconds. Once the copier is ready, theCHAPTER1 GETTING STARTED Power on and off Auto power shut-off mode POWER ON AND OFFPower save modes Preheat modePress the INFORMATION key in the standby mode INFORMATION FUNCTION~200g/m2 CHAPTER1USING THE TOUCH PANEL How to use the touch panelSelection of function particular settings for these functions Function setting iconsUSING THE TOUCH PANEL the basic screen. The setting screen for a selected functionFACE UP/FACE DOWN DELIVERY 1-10CHAPTER1 EXPOSURE ADJUSTMENTS MAKING COPIESUSING THE RSPF CHAPTERmanual for the printer auditing mode setting AUDITING ACCOUNTSSee page 8-14 for account limit settings KEY OPERATORUSING THE RSPF Stream feeding mode2. Different copy image ranges Ensure that the 1-sided to 1-sided copying mode is USING THE RSPFAdjust the original guides to the size of the originals and 1-sided copies of 1-sided originalsAdjust the original guides to the size of the originals and AUTOUSING THE RSPF 2-sided copies from 1-sided originals2-sided copies from 2-sided originals USING THE RSPFUsing the RSPF Press the 2-SIDED COPY key Press the key on the touch panel1-sided copies from 2-sided originals USING THE RSPFAdjust the original guides to the size of the originals and 1 set the originals face up in the document feeder tray1-sided copies of 1-sided originals COPYING FROM THE DOCUMENT GLASSEnsure that the 1-sided to 1-sided copying mode is Open the document feeder cover and place an original2-sided copies from 1-sided originals 1 glass, using the centring scale to position itCOPYING FROM THE DOCUMENT GLASS Use the 10-key pad to enter the desired number of 4 copiesCOPYING FROM THE DOCUMENT GLASS 2-10key indicator lights up, and 3 Press the 2-SIDED COPY key 4 Press the key on the touch panelAutomatic selection REDUCTION/ENLARGEMENT/ZOOM2-11 100%A. Preset reduction copy ratios are 86%, 81%, and 70% 77% and 64% 2-12100 % A. Preset reduction copy ratios are 50% and 25% 95%, 50%, and 25%REDUCTION/ENLARGEMENT/ZOOM 2-13141 % 5 Press the “OK” keyPlace the original in the document feeder tray or on the SPECIAL PAPERS manual feed2-14 1 document glass 2 Open the bypass trayTwo-sided copying with bypass tray 2-15SPECIAL PAPERS manual feed 5 then select the bypass trayText mode EXPOSURE ADJUSTMENTS2-16 Photo modeSORT mode SORT/GROUP2-17 GROUP modeStoring a job program JOB MEMORY2-18 1 Press the PROGRAM P keyTo cancel deletion, press the “CANCEL” key 2-194 Press the “EXIT” key to exit the job memory mode CANCEL DELETE STOREWhen the copier stops, remove the originals and set INTERRUPTING A COPY RUN2-20 When the interrupt copy run is complete, press theCHAPTER SPECIAL FUNCTIONSSETTING REVIEW XY ZOOMELECT XY ZOOM100% XY ZOOM100 % XY ZOOM50 % 141%1 document glass MARGIN SHIFTPlace the original in the document feeder tray or on the Press the SPECIAL MODES keyMARGIN SHIFT Select the desired shift amounts using the and 5 keysSIDE Press the “MARGIN SHIFT” key on the touch panelPlace the original in the document feeder tray or on the ERASEAB A B 1 document glassAdjust the amount of edge erase and/or centre erase if CANCEL OKSelect the desired erase mode ERASETRANSPARENCY INSERTS DUAL PAGE COPYINGDUAL PAGE COPY Place the originals on the document glass with theReplace the finished original with the next original after DUAL PAGE COPYINGPress the START key Ensure that the desired tray is selectedPress the 2-SIDED COPY key and select a duplex mode MULTI SHOT3-10 AUTOPress the “MULTI SHOT” key on the touch panel 3-11MULTI SHOT Select the number of originals to be included on onePress the START key 3-12MULTI SHOT Replace the finished original with the next original afterREADY TO CO COVERS3-13 2 duplex mode if needed. Press the “OK” key to close theSelect cover placement NCEL3-14 T ON FRONT COVER?READY TO CO 3-15TRANSPARENCY FILM WITH INSERT SHEETS Press the SPECIAL MODES key5 Press the upper “OK” key 3-16TRANSPARENCY FILM WITH INSERT SHEETS 6 Load transparency film into the bypass tray1 document glass PAMPHLET COPY3-17 Press the SPECIAL MODES keyPress the “PAMPHLET COPY” key on the touch panel 3-18PAMPHLET COPY Select the type of originalsCheck the copy paper selection 3-19PAMPHLET COPY Enter the desired number of copies Press the START keyIf a duplex copy mode is required, it must be selected at IMAGE EDITING FUNCTIONS3-20 AUTOMake all other desired copy mode selections and enter NCEL OK T ON FRONT COVER?3-21 IMAGE EDITING FUNCTIONSCENTRING 3-22IMAGE EDITING FUNCTIONS Press the START keyG REPEAT COPY 3-23IMAGE EDITING FUNCTIONS 2 select the desired paper sizeREPEAT COPY 3-24IMAGE EDITING FUNCTIONS Press the START keyAUTO 3-25IMAGE EDITING FUNCTIONS POSURESelect a type of border line 3-26IMAGE EDITING FUNCTIONS 8 Press the upper “OK” keyIMAGE EDITING FUNCTIONS 3-27READY TO CO B/W REVERSEOK OK 3-28IMAGE EDITING FUNCTIONS CENTRING3-29 C D E FBINDING CHANGE AUTO 3-302 sided copy mode IMAGE EDITING FUNCTIONSOK OK 3-31IMAGE EDITING FUNCTIONS CENTRINGREADY TO CO TEXT STAMP3-32 DATETEXT STAMP CANCEL OK3-33 Press the “TEXT STAMP” key on the touch panelDATE 3-34TEXT STAMP Select the print directionUrgent 3-35READY TO CO TEXT STAMPAdjust the darkness of the background of the stamp 3-36To adjust the exposure and print position, press the TEXT STAMPTEXT STAMP 3-37CANCEL OK POSITION DATETEXT STAMP 3-38Draft WATERMARKAdjust the darkness of the watermark 3-39To adjust the exposure, press the “OPTION” key TEXT STAMPTEXT STAMP 3-40CANCEL OK Press the lower “OK” keyPAGE NUMBER 3-41READY TO CO TEXT STAMPPress the “PAGE NUMBER” key on the touch panel 3-42TEXT STAMP Select the desired page number formatOK 9 Press the upper “OK” key 3-43TEXT STAMP PAGEEnsure that the two copiers are connected through the TANDEM COPY3-44 1 tandem-connection cable and they have been turned on7 copier is installed in the sub copier 3-45Make all other desired copier settings and enter the DUAL PAGE COPY TRANSPARENCY INSERTS100% SETTING REVIEW3-46 COPY RATIOPAPER SUPPLIESCHAPTER Loading copy paperPAPER Types and sizes of copy paperLoading copy paper Loading paper in paper trays 1 and Only use paper within the Sharp specification andPAPER 1 Gently lift and pull out the paper trayPAPER Adjust the paper size indicator to match the paper size 2 to be setAdjust the front guide and left guide while squeezing Changing the copy paper size in the tray1 Open the front cover ADDING TONERGENUINE SUPPLIES Pull down the toner hopper lock lever and pull the tonerPull on the sealing tape to remove it ADDING TONERSlide the toner cartridge along the guides over the toner hopper Slide the empty toner cartridge back along the guides and remove itDisengage and remove the container from the copier USED TONER DISPOSALInstall a new toner collecting container until it clicks into 3 placeProper storage STORAGE OF SUPPLIESPhotoconductive drum GENUINE SUPPLIESTROUBLESHOOTING COPIER TROUBLE?MAINTENANCE REQUIRED CHAPTERFirst confirm the misfeed locations MISFEED REMOVALMisfeed in the RSPF An original misfeed may occur at one of two locationsOpen the paper guide MISFEED REMOVALA Open the feeding roller cover Rotate the roller in the direction of the arrow and gentlyB Unlock the lever and open the transport cover MISFEED REMOVALOpen the document feeder and gently remove the misfed original Gently remove the misfed originalFOR RECOVERY INSTRUCTIONS Open and close the front cover to cancel the misfeed 2 displayFOR RECOVERY INSTRUCTIONS MISFEED REMOVALMisfeed in the transport area Open and close the front cover to cancel the misfeed 5 displayMISFEED REMOVAL Remove the misfed paperClose the front cover MISFEED REMOVAL2 Remove the misfed paper CHAPTER51 Open the front cover Misfeed around the fusing unit and exit areaMISFEED REMOVAL 2 Open the exit area cover carefully 3 Remove the misfed paperMISFEED REMOVAL 4 Close the exit area cover Close the front coverCHAPTER5 MISFEED REMOVAL 5-10FOR RECOVERY INSTRUCTIONS Misfeed in the reversing areaMisfeed in the duplex module 5-11MISFEED REMOVAL 3 Close the exit area cover and the left side coverMISFEED REMOVAL 5-12Open and close the front cover to cancel the misfeed 4 display 3 Close the exit area coverMAINTENANCE REQUIRED 5-13CHAPTER5 COPIER TROUBLE? Maintenance required TROUBLESHOOTING 5-14CHAPTER5 COPIER TROUBLE? Troubleshooting Self-diagnostic function 5-15TROUBLESHOOTING CONFIGURED TO PERFORMPage TOUCH PANEL CONTRAST ADJUSTMENT GENERAL INFORMATIONUSER MAINTENANCE SPECIFICATIONSExterior PART NAMES AND FUNCTIONSPower switch CHAPTER6PART NAMES AND FUNCTIONS Interior Fusing unitAccessories Transport leverFunction setting icons p.1-9 INTERRUPT key and indicator pSTART key and indicator PART NAMES AND FUNCTIONS Operation PanelInitial settings can be CUSTOM SETTINGS keyInitial settings PART NAMES AND FUNCTIONS Touch Panel Basic screenUSER MAINTENANCE Document glass and document feeder coverRSPF scanning section Press the “LIGHTER” or “DARKER” key to adjust the contrast TOUCH PANEL CONTRAST ADJUSTMENT1 Press the CUSTOM SETTINGS key Touch panel contrast adjustmentSPECIFICATIONS COPIERCHAPTER6 DUPLEX MODULE SPECIFICATIONSDOCUMENT FEEDER CHAPTER6Page CHAPTER OPTIONAL EQUIPMENTSYSTEM CONFIGURATION FINISHER AR-FN3SYSTEM CONFIGURATION CHAPTER7FINISHER AR-FN3 SpecificationsPART NAMES When copying in the SORT mode, each collated set of OFFSET modeNON-OFFSET mode inch from the previous set. When copying in the GROUPSTAPLE SORT mode SORT modeGROUP mode FINISHER AR-FN3Staple sort Using the RSPFFINISHER AR-FN3 AUTOSelect the desired stapling position FINISHER AR-FN3STAPLE SORT SORT GROUP Press the “OK” key Set the number of copies Press the START keySTAPLE SORT SORT GROUP Using the document glassFINISHER AR-FN3 2 Press the OUTPUT key6 Set the number of copies key indicator lights up, and then pressFINISHER AR-FN3 7 Press the STARTFINISHER AR-FN3 7-10Staple cartridge replacement Lower the lock lever to unlock the stapler unitInsert the staple box into the stapler unit until it clicks 7-11FINISHER AR-FN3 9 into placeStaple jam removal 7-12FINISHER AR-FN3 Lower the lock lever to unlock the stapler unit7 Return the lever to its original position 7-13FINISHER AR-FN3 8 place Lower the lock lever and return the stapler unit to faceMisfeed removal 7-14FINISHER AR-FN3 Misfeed in the upper transport areaIf the misfed paper cannot be removed in step 2, open 7-15FINISHER AR-FN3 3 the cover of the paper feed area of the finisherFINISHER AR-FN3 7-16FOR RECOVERY INSTRUCTIONS Misfeed in the lower transport areaRemove the misfed paper 7-17FINISHER AR-FN3 4 Close the transportClose the paper transport area cover 7-18FINISHER AR-FN3 Roller rotating knobSpecifications LARGE CAPACITY TRAY AR-LC1N7-19 PART NAMESOPTIONAL EQUIPMENT7 Large capacity tray AR-LC1N CHAPTERMisfeed removal 7-21LARGE CAPACITY TRAY AR-LC1N Remove any misfed paper from the copier and the large capacity trayIf misfed paper is not found in step 2, pull the tray out 7-22LARGE CAPACITY TRAY AR-LC1N Remove the misfed paper Gently push the tray back into placeSTAND/500-SHEET PAPER DRAWER AR-DE7 7-23Specifications PART NAMES7-24 STAND/500-SHEET PAPER DRAWER AR-DE7Loading copy paper FOR RECOVERY INSTRUCTIONS 7-25Open and close the front cover to cancel the misfeed display STAND/500-SHEET PAPER DRAWER AR-DE7Page CHAPTER KEY OPERATOR’S GUIDEFACTORY SETTING KEY OPERATOR CODE NUMBER1 Press the CUSTOM SETTINGS key KEY OPERATOR CODE NUMBER6~200g/m2 Enter your key operator code number using the 10-key 3 padPress the “KEY OPERATOR CODE NUMBER CHANGE.” 6 key Choose a new 5-digit code number and enter it using the 10-key padKEY OPERATOR CODE NUMBER Press the OK keyKEY OPERATOR PROGRAMS KEY OPERATOR’S GUIDE8KEY OPERATOR PROGRAMS KEY OPERATOR PROGRAMS CUSTOM SETTINGS Using the key operator programs1 Press the CUSTOM SETTINGS key 6~200g/m2Press the key of the desired program on the touch panel KEY OPERATOR PROGRAMSSelect the desired category on the touch panel Follow instructions for the programKEY OPERATOR PROGRAMS ACCOUNT CONTROLAuditing Mode Number of Copies per AccountBilling by Account 8-10KEY OPERATOR PROGRAMS 1. Press the key to advance through the accountsTo reset all accounts 8-11KEY OPERATOR PROGRAMS Resetting Account To reset a single accountKEY OPERATOR PROGRAMS Account Number Control 8-122. Enter a 5-digit account number 00001 to 99999 using the 10-key pad To register accounts2. Enter the account number to be changed using the 10-key pad 8-13Price/Copy Setting KEY OPERATOR PROGRAMSKEY OPERATOR PROGRAMS 8-14Account Limit Setting To set a limitTo set a limit for all accounts 8-15KEY OPERATOR PROGRAMS Account Number SecurityExposure Adjustment OTHER FUNCTION SETTINGS8-16 1. Adjust the exposure using the and keys 2. Press the “OK” keySetting a Maximum Number of Copies 8-17KEY OPERATOR PROGRAMS Add or Change Extra Preset Ratios 1. Input the number using the 10-key padErase Width Adjustment 8-18KEY OPERATOR PROGRAMS Initial Margin Shift Setting 1. Adjust the value for each side using the and keysTo establish new initial settings 8-19KEY OPERATOR PROGRAMS Initial Status Setting To return to the factory default settingsDate Format Setting 8-20KEY OPERATOR PROGRAMS Staple Position Setting 1. Select the desired stapling position on the touch panelRotation Copy Setting 8-21KEY OPERATOR PROGRAMS Date and Time Adjustment 1. Select an item to be adjusted and adjust the value using2. Select a paper size for EXTRA setting 8-22KEY OPERATOR PROGRAMS Size Setting for EXTRA Heavy Paper on the Bypass TrayAuto Power Shut-off Timer TIMER SETTINGS8-23 Auto Clear SettingNoise Level Reduce Mode 8-24KEY OPERATOR PROGRAMS Preheat Mode Setting 1. Set the desired time interval using the and keys8-25 KEY OPERATOR PROGRAMS Message Time Setting1. Set the time using the and keys 2. Press the “OK” key Disabling of Auto Tray Switching ENABLE/DISABLE SETTINGS8-26 KEY OPERATOR PROGRAMSDisabling of Document Feeder 8-27KEY OPERATOR PROGRAMS Disabling Deletion of Job Programs Disabling of Duplex CopyingDisabling of PC/Modem Access 8-28Disabling of Covers Mode KEY OPERATOR PROGRAMS Disabling of StaplerDisabling of Beep When Keys Touched 8-29Disabling of Auto Power Shut-off Mode To disable the auto power shut-off mode, press the check box of “DISABLING OF AUTO POWER SHUT-OFF MODE.” to display a check mark in the check boxKEY OPERATOR PROGRAMS OTHER PROGRAMS8-30 Total CountTHE FINISHER IS OUT OF SERVICE. PRESS CA TO CANCEL JOB KEY OPERATOR ASSISTANCE CALL8-31 THE DOCUMENT FEEDER IS OUT OF SERVICE. PRESS CA TO CANCEL JOBMEMO 8-32Factory setting = KEY OPERATOR CODE NUMBER FACTORY SETTING8-33 KEY OPERATOR Detach this page and store it in a safe place2000C DSC1 CINSE1982FC51 MAINS PLUG WIRING INSTRUCTIONS GREEN-AND-YELLOW Earth BLUENeutral BROWNLivePRINTEDIN JAPAN SHARP CORPORATIONAR-507 Sharp House, Thorp Road, Newton Heath, Manchester M40 5BE