Sharp DV-RW2U Setting the Manufacturer’s Code, Setting the Remote, Control Code of the Recorder

Major Components

POWER	TIMER	DISC	OPEN/
	ON/OFF	TIMER	CLOSE
ANGLE	AUDIO	CH
SETUP/	DNR	ZOOM	INPUT
FUNCTION
TITLE			MENU
RETURN			SET/
			ENTER
			VCR PLUS+
		TIMER PROG.
			REC MODE
AM/PM		ERASE PROGRAM
100
REV			FWD
	PLAY
REC			STILL/PAUSE
	STOP
SKIP	F.ADV		SLOW
SEARCH	SKIP
DISPLAY	ON	ORIGINAL/	EDIT
	SCREEN	PLAY LIST
POWER	INPUT	VOL

CH

TV CONTROL

Operating a TV Using the

Remote Control

(Universal Remote Control)

The Universal Remote Control may operate the basic functions of 21 different types of TVs.

To enter the Manufacturer’s Code for your TV, follow the instructions below.

There is no guarantee that the universal remote control will function with your TV.

Setting the Manufacturer’s Code

1 Press POWER and CH ' of TV

CONTROL simultaneously.

2 Enter the 2-digit Manufacturer’s Code with the number buttons (Ex. 02-“0”, “2”) within 10 seconds after releasing POWER and CH ' of TV CONTROL.

3 Point the remote control unit towards the TV and then press POWER of TV CONTROL.

•If the TV turns on/off, setup was successful. If not, repeat the proce- dure using another code.

Setting the Remote

Control Code

•There are two types of codes (remote control codes) for operating this recorder with the remote control (RC1 and RC2). If you operate this recorder with the remote control while using with another SHARP DVD recorder or DVD player placed next to it and both units end up being operated simultaneously, switching the remote control code (for both the recorder and the remote control) to one of the two signals (RC1 or RC2) will let you operate only the recorder.

•Make sure to set the recorder and remote control to the same remote control code. You will not be able to operate the recorder with the remote control if different remote control codes are used.

Important!

If the remote control codes of the recorder and remote control are different, the remote control code will flash on the display of the recorder. Reset the remote control number to the code flashing on the display.

Note

•The remote control code of the remote become “RC 1” when you change the batteries.

Setting the Remote

Refer to the list below for the Manufacturer’s Code and the buttons which work with each brand.

Buttons on the Remote		POWER
		CH '/" INPUT
Brand	Code	VOL	/
EMERSON	19	⋅	⋅
FISHER	17	⋅	⋅
FUNAI	06	⋅	⋅
GE	07, 09	⋅	—
GOLDSTAR	18	⋅	—
HITACHI	15	⋅	⋅
JVC	16	⋅	⋅
MAGNAVOX	09	⋅	—
	11	⋅	⋅
MITSUBISHI	14	⋅	⋅
PANASONIC	13, 21	⋅	⋅
PIONEER	03	⋅	⋅
RCA	07, 09	⋅	—
SAMSUNG	20	⋅	⋅
SANYO	17	⋅	⋅
SHARP	01	⋅	⋅
	02	⋅	⋅
SONY	10	⋅	⋅
TECHNOL ACE	04	⋅	⋅
TOSHIBA	12	⋅	⋅
ZENITH	05	⋅	⋅
	08	⋅	—

NOTE

•If the batteries in the remote control unit are changed, the code settings must be re-entered.

•Some brands have more than one code listed above, due to changes in the codes. In such cases, try another code to find the code that operates your TV.

18

Control Code of the Recorder

1 Press POWER to turn off the recorder.

2 Press and hold CHANNEL" and

'on the recorder together for more than 5 seconds.

• Each time the button is pressed, the code of the recorder toggles between “RC-1” and “RC-2”.

• At this point, the recorder can no longer be operated with the remote control. Next, set the remote control code for the remote control.

Setting the Remote

Control Code of the

Remote

Example: Setting the “RC2”.

1 Press and hold POWER and 2

together for more than 5 seconds.

•When you set the code to “RC1”, press and hold POWER and 1 together.

2 The recorder is turned on.

DV_RW2U#p12-18.p65 18 03.1.14, 9:17 AM