Sharp JW-20CM, JW-20RS 9-6Setting contents of slave station parameters, Contents, Setting item

9-6 Setting contents of slave station parameters

※1

※2

9

When the JW-20CM is used as a slave station, set the following items for parameters.

	Setting item			Initial	Contents		Corresponding
			Address(8)				signs on pages
				value (H)
							11·7 and 11·8
①	Setting time-out item of SEND/		007500	00	For using SEND/RECEIVE instruction, set the
	RECEIVE instruction		to		time out time by decimal.
			007577		[001 (0.1 sec..) to 255 (25.5 sec.)]
	Setting PC model of each		007600		91(H): The PC is JW type and ZW-20CM has
②	station in SEND/RECEIVE		to	91	JW mark or JW-20CM or JW-22CM
	function		007677		81(H): The PC is ZW type and ZW-20CM
					has JW mark or JW-20CM.
					00/81(H):ZW-20CM without JW mark
	Select system of each channel		007700	00	Select instruction system or data memory starting
③	in SEND/RECEIVE function		to		system in CH0 to CH3
		V5	007703
	Top addresses in communi-		007710		Setting by file number and file address.
	cation information storage area				· Setting within communication information
④	when using data memory start-		to	00	storage area (64 bytes)
	ing system of SEND/RECEIVE		007713		File 0: 000000 to 015777(8)
					File 1 to 7: 000000 to 177777(8)
	functions	V5
	Number of receiving bytes of				Set the number of bytes by decimals. (0 to 64)
⑤	relay link in memory capacity		007720	00	· If 0 is set, the number of bytes will be the same		h1 to hn
	save function		007721		as the number of the sending bytes which is set
		V5			in the master station
	Number of receiving bytes of				Set the number of bytes by decimals. (0 to 512)
⑥	register link in memory		007722	00	· If 0 is set, the number of bytes will be the same		i1 to in
	capacity save function		007723		as the number of the sending bytes which is set
		V5			in the master station
	Top address of relay link		007730		Set by file number and file address.		f1 to fn
⑦	area		to	00	(See page 13·20 and 13·21)
		V5	007733
	Top address of register link		007734	00	Set by file number and file address.		g1 to gn
⑧	area		to		(See page 13·20 and 13·21)
		V5	007737
⑨	Whether the station number			00	Store the number of own station in the data memory
	information should be output		007763		when setting on 01(H). (storage area of 1 byte follows
	or not	V2			flag area of 24 bytes, valid when 007767(8) is 80(H))
			007764	E0	Lower of file address	Initial value: 01E0(H)
	Top address of flag area		007765	01		↓
					Upper of file address	007767(8) (ｺ0740)	e1 to en
⑩	(communication and PC
				00
	operation condition monitor		007766		File number
	flag)		007767	80	Flag output (Yes: 80(H) No: 00(H))
⑪	Communication error		007771	00	Settable detection interval with 100 ms pitch
	detection interval				00(H): Stop remote I/O operation
					01(H): Start remote I/O operation
⑫	Writing to the EEPROM,		007777	01	80(H): Writing to the EEPROM, stop operation
	start operation/stop setting
					81(H): Writing to the EEPROM, start operation
					08(H): Initialize the parameter

※1 Set only any of JW50/70/100 or JW50/70H/100H is used as PC, and using SEND/RECEIVE instruction.

※2 Set only any of JW50/70/100 or JW50/70H/100H is used as PC, and using the memory capacity save function.

① to ⑫ correspond to numbers in the next page.

9·22