(3)Error code

When an error occurs in the JW-20CM, it stores the occurred error’s code to system memory #170 of each station’s PC.

Error

Cause

Error code stored to system memory(H)

 

Measure

 

 

code

 

 

 

 

 

 

 

 

 

(HEX)

 

#160

 

#170 to 177

 

 

 

 

01

ROM error, upper CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

02

RAM error, upper CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace the JW-20CM

 

 

03

2 port RAM error against PC, upper CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

04

2 port RAM error against

53

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

communication CPU, upper CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Check the communication

 

 

11

ROM error, communication CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cable

 

 

12

RAM error, communication CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Check for doubled allocation

 

 

 

 

 

 

 

 

 

 

 

 

 

18

Communication LSI error, communication CPU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

of slave station number

 

 

1F

No response

 

 

 

 

1F

 

• Replace the JW-20CM

 

 

 

 

 

 

 

 

 

20

More than one token detected

 

 

 

20

 

Check the parameter setting

 

 

 

 

 

 

 

 

21

Doubled address detected

 

 

 

21

 

 

 

 

 

 

 

 

 

 

 

22

Fault of sending section

 

 

 

22

 

Replace the JW-20CM

 

 

 

 

 

 

 

 

23

Token does not return within the rated interval

 

 

 

23

 

Check the communication cable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2A

Over flow of receiving buffer.

 

 

 

 

2A

Check the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2B

Flame length error of receiving

 

 

 

 

2B

 

 

 

 

 

 

communication cable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2C

Media error

 

 

 

 

2C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

EEPROM error

 

 

 

30

 

Replace the JW-20CM

 

 

 

 

 

 

 

 

6E

BCC error

 

 

 

 

6E

Check the parameter setting

 

 

 

 

 

 

 

 

6F

Parameter setting error

 

 

 

 

6F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C1

Communication error

 

 

 

 

C1

Check the communication

 

 

to

• After converting into octal, the lower two digits

 

 

 

 

to

 

 

represent the slave station number of the current

 

 

 

 

cable and slave module

 

 

 

 

 

 

9

 

 

 

 

 

 

 

 

FF

error. (Ex. C1(H) = 301(8)= slave station 01)

 

 

 

 

FF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

· In some cases, error code 23(H) or 2A(H) is stored when inputting power. This is not an error.

Remarks

The error code stored in the system memory #170 is shifted to #170 to #177 one after the other as new errors occur. Thus, the system memory can store up to 8 errors. When the PC is operating by RAM, these error codes do not disappear even after turning OFF the power.

The contents of system memory #170 to #177 are kept storing after the JW-20CM recovers from the error.

#177 #176 #175 #174 #173 #172 #171 #170

6E Occurrence of BCC error

Disappear

 

6E

6F

Occurrence of parameter

 

setting error

 

 

 

 

 

 

 

 

 

 

 

 

9·61