(I/O error code of JW model)

 

 

LED name

 

 

Error

Cause

Measure

80

40

20

10

8

4

2

1

code

(HEX)

 

 

●

○

○

●

○

●

●

●

97(H)

I/O table error

Register I/O table

 

Replace the JW-20RS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

●

○

○

●

●

○

○

○

98(H)

Input data parity error

Replace basic rack panel,

●

○

○

●

●

○

○

●

99(H)

Output data error

extension cable, I/O

 

 

 

 

 

 

 

 

 

 

 

●

○

○

●

●

○

●

○

9A(H)

I/O table registration error

module, or register I/O

 

 

 

 

 

 

 

 

 

 

 

●

○

○

●

●

○

●

●

9B(H)

Special I/O module error

table.

 

 

 

 

 

 

 

 

 

 

 

●

○

○

●

●

●

○

○

9C(H)

Blown fuse

Replace the fuse

•When error numbers 98 through 9C(H) occur, the module will store “rack No.” and “slot No.” in the parameter address 005000(8) in the JW-20RS.

Parameter address D7 D6 D5 D4 D3 D2 D1 D0

005000(8)

Rack No.

Slot No.

When more than one module has and error, the lowest “rack No.” and “slot No.” will be stored.

•A special I/O module error (9B(H)) can be detected by the JW-2DA/8AD/11DU/12DU/12PM. When the JW-2DA/12PM detects this error, you can also assume that there is a problem in the 24 V power supply.

•A fuse blown error (9C(H)) can be detected by JW-12S/13S/32S/33S/35S.

If the error cannot be eliminated after replacing the module in which the error occurred, check the modules in the JW-20RS and then in the rack panel.

③PC body and JW-20CM, JW-20RS

8

The operating status of the remote master station and slave stations will vary according to the

 

operation, stop, error, and power failure conditions in the PC as follows. For output hold switch in

 

 

detail, see page 8·15

 

 

 

 

●: Light ON, ×: Blinks, No mark: Lights OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power supply

 

PC body

 

 

JW-20CM Indication lamps

 

 

 

 

module

 

 

 

 

 

 

PC body

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicator

 

System

 

 

 

 

 

 

 

 

 

 

operational

Halt

Power

 

 

 

 

 

 

 

 

 

 

 

Flag

memory

 

 

 

 

 

 

 

 

 

 

condition

output

lamp

Operating

Error

relay

#170 to

COMM

SD

RD

CD

ERROR

TEST

FAULT

S0 to

 

 

 

HALT

POWER

RUN

FAULT

 

#177

 

 

 

 

 

 

 

S7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operating at normal

Close

●

●

 

ON

Hold

●

×

×

×

 

 

 

 

 

 

Stop at normal

Open

●

×

 

ON

Hold

●

×

×

×

 

 

 

 

 

 

Error

Open

●

 

●

Not fixed

Hold

●

×

×

×

●

 

 

 

 

 

Remote master

Open

●

 

●

Not fixed

Hold

●

 

 

 

 

 

●

 

 

 

station error

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power supply

 

 

JW-20RS Indication lamps

 

 

 

 

 

 

 

module

 

 

 

 

 

 

 

 

PC body

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Halt

Power

Condition of output module

 

 

 

 

 

 

 

 

 

 

operational

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

condition

output

lamp

Output hold

Output hold switch

COMM

SD

RD

CD

ERROR

TEST

FAULT

S0 to

 

 

 

HALT

POWER

switch “HOLD”

“RST”

 

 

 

 

 

 

 

S7

 

 

Operating at normal

Close

●

－

 

－

●

×

×

×

 

 

 

 

 

 

Stop at normal

Open

●

Hold

Reset

 

×

×

×

 

 

●

※

 

 

Error

Open

●

Reset

Reset

 

×

×

×

●

 

●

Error

 

 

 

 

code

 

 

Remote master

Open

●

Reset

Reset

 

Not fixed

●

 

●

Error

 

 

station error

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PC power in OFF

Open

●

Reset

Reset

 

Not Fixed

●

 

●

Error

 

 

 

 

code

※When the JW-20RS fault lamp is lit and no error code is displayed, it might be the case that the PC has stopped operation (in the program mode).

8·50