Sharp JW-20CM, JW-20RS (3)Parameter setting of slave module (JW-20RS)

(3)Parameter setting of slave module (JW-20RS)

Set the following parameter address after setting switch. Setting item varies with using I/O module (JW model or ZW model).

O:Necessity for setting

Item	Address	Initial value		Setting contents	JW-I/O	ZW-I/W	See page
	(8)	(H)
			0 : No. of dummy I/O points : No points
			1 : No. of dummy I/O points : 16 points (2 bytes)
			2 : No. of dummy I/O points : 32 points (4 bytes)
			3 : No. of dummy I/O points : 48 points (6 bytes)
			4 : No. of dummy I/O points : 64 points (8 bytes)
Setting no. of dummy I/O	000000		5 : No. of dummy I/O points : 80 points (10 bytes)
points			6 : No. of dummy I/O points : 96 points (12 bytes)
· Use 1 byte per vacant	to	00	7 : No. of dummy I/O points : 112 points (14 bytes)		○	－	8・25
2 slots			8 : No. of dummy I/O points : 128 points (16 bytes)
· Set at only manual I/O
	000017		9 : No. of dummy I/O points : 144 points (18 bytes)
table registration
			A : No. of dummy I/O points : 160 points (20 bytes)
			B : No. of dummy I/O points : 176 points (22 bytes)
			C : No. of dummy I/O points : 192 points (24 bytes)
			D : No. of dummy I/O points : 208 points (26 bytes)
			E : No. of dummy I/O points : 224 points (28 bytes)
			F : No. of dummy I/O points : 240 points (30 bytes)
			91	: 16 points output
			92	: 32 points output
Set kinds of I/O module	000100		94	: 64 points output
			00	: Vacant slot (lower is dummy I/O points)
· Use 1 byte per slot
	to	00	A1 : 16 points output		○	－	8・26
· Set at only manual I/O
			A2 : 32 points output
table registration	000137
			A4 : 64 points output
			D1 : Special I/O module
			F1 : Special I/O module
								8
Set max.racks and slot	001000	00	Upper 4 bits : Rack number		○	－	8・28
number			Lower 4 bits : Slot number
			60	: Manual setting for both dummy I/O points and
				kinds of I/O module
Set manual I/O table			64	: Manual setting for dummy I/O points and
	001001	00		auto setting for kinds of I/O module	○	－
registration
			65	: 00 for dummy I/O points and auto setting for			8・27
				kinds of I/O module
			00	: When setting is normal end
Register automatically or			00	: Auto registration
not I/O table at power	001002	00			○	－
			03	: Prohibit the auto registration
input.
Set remote I/O top	001004	00	Set file address in octal when only using search		○	－	8・29
address	001005		module (SU) lamp.
Check no. of I/O bytes	003750	00	00	: No check the no. of I/O bytes	－	○
			45	: Check the no. of I/O bytes
	003752	00	If "checking number of I/O bytes to be used by the				8・24
			I/O module" function is selected to "not to check"
Set no. of I/O bytes					－	○
	003753	00	using decimal notation 000 to 128, this setting is
			not needed.
			00	: Stop remote I/O operation
Writing to the EEPROM,			01	: Start remote I/O operation			8・22
start operation/stop	003777	01	80	: Writing to the EEPROM, stop operation	○	○
							8・23
setting.			81	: Writing to the EEPROM, start operation
			08	: Initialize the parameter

· There is no difference of parameter setting between "fixed allocation" and "manual allocation."

8·19