Sierra Wireless EV-DO Other

PinPoint-E EV-DO

141 20070914

Other

Figure 1-14: AceManager : Other

DAE=n

ATEscapeSequencedetection.

•n=0:Enable

•n=1:Disable

*DATZ=n

EnablesordisablesresetonATZ.

•n=0:NormalReset(Default).

•n=1:DisableResetonATZ.

*IPPING=n

Settheperiodtoping(ifnovalidpacketshavebeenreceived)a

specifiedaddress(*IPPINGADDR)tokeepthemodemalive

(online).

•n=0:Disablepinging(default)

•n=15‐255minutes

Note: 15 minutes is the minimum interval which can be set for

Keepalive. If you set *IPPING for a value between 0 and 15, the

minimum value of 15 will be set.

Contents

Main Important Notice Safety and Hazards Limitation of Liability Patents Copyright Trademarks QUALCOMM 3G Contact Information Revision History Contents Activating your PinPoint-E on the Verizon Network . . . . . . . . . . . . . . . . . . . .22 Data Communication and Host Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Rev 3.0B Feb.08 3 SNMP : Simple Network Management Protocol . . . . . . . . . . . . . . . . . . . . . .103 Rev 3.0B Feb.08 5 Rev 3.0B Feb.08 6 Rev 3.0B Feb.08 7 Rev 3.0B Feb.08 8 1: Introduction to the PinPoint-E ALEOS AceWare AceManager Page AceNet AceView Page Modem Doctor USB Connecting to the Verizon Network Dynamic vs. Static IP Addresses EV-DO Communication Page 2: Specifications Interface Port Pin-Outs Power Connector Interface Port Pin-Outs Page 3: Activating your PinPoint-E on the Verizon Network Automatic Activation Setup Wizard Activating Using AT Commands Automatic Activation Setup Wizard 1. Wizard: Starting the Setup Wizard 2. Wizard: Connecting to the Modem 3. Wizard: Selecting Tasks 4. Optional: Wizard: Update ALEOS 5. Wizard: Activate Modem 6. Wizard: Test Modem Setup 7. Setup Private Networking (C3x10) Activating Using AT Commands Page 4: Hardware Installation of the PinPoint-E GPS Connecting to Power Connecting to a Computer or other Device Indicator Lights Page Mounting Page 5: Configuring your PinPoint-E Using AceManager Using Templates Using a Terminal Application with AT Commands Using AceManager 1. Start AceManager 2. Connect to your PinPoint-E 3. Enter the configuration options 4. Write the changes to the modem Using Templates 1. Creating the Template with AceManager Page 2. Applying a Template to one modem with AceManager 3. Optional: Applying one template to several modems simultaneously with AceNet Page Using a Terminal Application with AT Commands 1. Choose a name and icon for your connection. Page Page 4. Connected AT Commands Page 6: Inputs, Relay Outputs, and Power Status Capturing External Events using Inputs Power Modes and Information Capturing External Events using Inputs Configuring the DTR and/or RTS Monitoring Connecting your device to the Serial Port e Power Modes and Information Wiring the PinPoint-E for DTR Event Tri g g e r Power Effect on Modem State 7: Data Communication and Host Modes Basic Modes Serial Modes Data Communication Basic Modes Start up Mode AT M ode PassThru Mode Te ln et M od e Serial Modes PPP Page SLIP UDP and UDP Pad Page TCP an d TCP Pad Hybrid Modes Page Data Communication Public and Private Mode Page Keepalive Page Page 8: IP Manager Understanding Domain Names Using IP Manager with your PinPoint-E Understanding DNS Understanding Domain Names Dynamic Names Using IP Manager with your PinPoint-E Data Usage for IP Manager Server Updates Eairlink.com Understanding DNS Configuring DNS The PPP-Peer Domain Name 9: Global Positioning System (GPS) GPS Overview PinPoint-E Supported Protocols Datum Before you Configure GPS Configuring the PinPoint-E for GPS Real-Time Clock Synchronization Configuring the Datum Over-The-Air (Remote) Host Local Host TCP GP S Report P olling Report Types Sending Reports Automatically Store and Forward Page RAP Configuration RAP Reports Over-The-Air (Remote) RAP Reports over a Local Connection Configuring Additional RAP Features Page Page NMEA Configuration Messages Over-The-Air (Remote) Local Host Streaming Messages (Local) Page TAIP Emulation Configuration TAI P ID TAIP Command Emulation Messages Over-the-Air (Remote) Local Connection Page Streaming Messages (Local) Page 10: SNMP : Simple Network Management Protocol SNMP Configuration SNMP MIB Definition Sample Management Information Base (MIB) SNMP Traps SNMP Configuration Listening Port Security Level User Name and Password Trap Destination Community String SNMP MIB Definition Sample Rev 3.0B Feb.08 107 Rev 3.0B Feb.08 108 Rev 3.0B Feb.08 109 Rev 3.0B Feb.08 110 Display Responses Object AT Com man d phoneNumber *NETPHONE? deviceID *DEVICEID? electronicID I3 aleosSWVer I1 Rev 3.0B Feb.08 111 Product ID A A: Configuration Commands Info (information) Page Information Displayed in AceManager without AT Commands Listed Status Page Information Displayed in AceManager without AT Commands Listed GPS Status and Map Link AT Commands Requiring PassThru mode Common Misc (Miscellaneous) Page Page Page Page Serial Page Page Page Page TCP UDP Page Page DNS Dynamic IP Page PPP/Ethernet Page PassThru Page Page Page Other Page Page Low Power Frie nds Logging Page PinPoint (GPS) Page Page Page Page Page 1x/EV-DO Page Page Page B B: Windows Dial-up Networking (DUN) Installing a modem driver for PinPoint-E 1. Connect the PinPoint-E. 2. Install the driver. Page Page Page Page Creating a Dial-Up Networking (PPP) Connection 1. Create a new network connection. Page Page Page Page Page Page Page Page Connecting to the Internet Using DUN AceView 1. Start AceView. 2. Enable the Connection. Windows DUN 1. Start the DUN session. 2. Select Dial to connect to the modem and the cellular network.