=0‐65535 hex | Sierra Wireless EV-DO manual

Configuration Commands

•n=0 : Disabled

•n=1‐65535

*PPFLUSHONEVT=n

Flushes store and forward buffer when an input event (DTR/

RTS) occurs.

•n=0 : Disable

•n=1 : Enable

*PPGPSDATUM=n

Specifies the GPS datum to use for position reports. For accurate results, this value should match the datum used by receiving mapping application.

•n=0 : WGS84

•n=92 : NAD27

•n=115 : NAD83

Note: This command may not be available for your PinPoint-E PinPoint or PinPoint-E. This requires specific internal hardware as well as a recent version of ALEOS.

*PPGPSSENTENCES=n

Specifies the NMEA sentences to display in the NMEA GPS

Report.

•n=0‐65535 (hex)

*PPGPSR=n

GPS report type.

•n=0x11 : Standard GPS Report

•n=0x12 : Standard GPS Report + UTC Date

•n=0x13 : Standard GPS Report + UTC Date + RF data

•n=0xE0 : GGA and VTG NMEA reports

•n=0xE1 : GGA, VTG and RMC NMEA reports

•n=0xF0 : TAIP reports

•n=0xF1 : Compact TAIP data

*PPIGNOREIP=n

When enabled, ignore ATS Server IP (*PPIP) updates in RAP.

•n=0 : Use ATS Server IP updates.

•n=1 : Ignore ATS Server IP updates.


Rev 3.0B Feb.08						150
Rev 3.0B Feb.08						150

Image 155

Sierra Wireless EV-DO manual =0‐65535 hex

Contents

User Guide Important Notice Safety and Hazards Limitation Liability Qualcomm 3G Patents Copyright Trademarks Contact Information Support@sierrawireless.com Revision Release Changes Number Date Revision History Contents Configuring your PinPoint-E IP Manager Snmp Simple Network Management Protocol 117 Contents Contents Windows Dial-up Networking DUN Introduction to the PinPoint-E AceManager AceWare Monitor and Control Simplified Deployment Network Monitoring AceNetAceView Modem Doctor Setup Wizard Modem Doctor Modem Doctor USB Steps of a connection Connecting to the Verizon Network Dynamic vs. Static IP Addresses Connecting to the Internet Security EV-DO Communication Introduction to the PinPoint-E Bands Features and BenefitsPower Consumption @12V DC Technology Interface Port Pin-Outs Serial Port Diagram Female DB-9 DCE not to scale Power Connector Automatic Activation Activating your PinPoint-E on 3 the Verizon Network Wizard Starting the Setup Wizard Setup Wizard Setup Wizard Ethernet Connection Wizard Connecting to the Modem Wizard Selecting Tasks Setup Wizard Serial Connection Setup Wizard Task Menu Optional Wizard Update Aleos Wizard Activate Modem Aleos Update Setup Wizard Otasp screen Wizard Test Modem Setup Setup Private Networking C3x10 11 Setup Wizard Primary and Secondardy HA Activating Using AT Commands Set telnet timeout in to 20 minutes Hardware Installation PinPoint-E GPS Connecting to a Computer or other Device Connecting to Power Serial Indicator Lights Light Patterns Rssi LED Ranges RSSI/Signal LED Status Ranges of Rssi dBm Optional Mounting Bracket Mounting Mounting Bracket for PinPoint-E Start AceManager Using AceManager AceManager Connect to Modem Connect to your PinPoint-E AceManager Connected Enter the configuration options Creating the Template with AceManager Using TemplatesWrite the changes to the modem · Cellular Technology specific settings the CDMA/EV‐DO group Applying a Template to one modem with AceManager Reset the modem Configuring your PinPoint-E 10 AceNet Selected modems Choose a name and icon for your connection Using a Terminal Application with AT Commands Connect To Port Settings serial only 15 Port Settings Connected AT Commands Configuring your PinPoint-E Configuring the DTR and/or RTS Monitoring Capturing External Events using Inputs Connecting your device to the Serial Port AceManager Low Power Power Modes and Information Power Effect on Modem State Wiring the PinPoint-E for DTR Event Trigger Serial Modes Basic Modes Data Communication Start up ModeBasic Modes AT Mode AceManager PassThru PassThru Mode Serial Modes Telnet Mode AT\APPP UDP Auto Answer UDP and UDP Pad Reliable UDP TCP and TCP Pad UDP Multicast Mode TCP Auto Answer Hybrid Modes Udplast Data Communication Public and Private Mode Internal Dhcp Server Keepalive Configuring Keepalive AceManager Other Data usage using Keepalive Minutes 100k / month 50k / month Reasons to contact the modem and/or the connected device IP Manager Understanding Domain Names Car54.mydomain.com.ca Dynamic NamesCar54.mydomain.com AceManager Dynamic IP Using IP Manager with your PinPoint-E Restrictions for Modem Name Data Usage for IP Manager Server UpdatesEairlink.com Understanding DNS Configuring DNS AceManager DNS PPP-Peer Domain Name GPS Overview GPS PinPoint-E Supported Protocols Remote Access Protocol RAP Trimble Ascii Interface Protocol Taip DatumNational Marine Electronics Association Nmea Before you Configure GPS Configuring the PinPoint-E for Real-Time Clock Synchronization Configuring the Datum Local Host Over-The-Air Remote Host Report Types TCP GPS Report Polling Remote Sending Reports Automatically Local Report Delay on Power-UpStore and Forward Sending Reports Based on an Interval Store and Forward Reliable Mode Flush on Event RAP Configuration RAP Reports over a Local Connection RAP Reports Over-The-Air Remote 16 AceManager Misc S53 Configuring Additional RAP Features Serial Input Event Reports Device IDOdometer Data in Reports Flush on Event COM 1000 support Messages Over-The-Air Remote Nmea Configuration 26 AceManager Misc S53 Port Streaming Messages Local 29 HyperTerminal Nmea Streaming Persistent Streaming Supported Taip Commands Taip Emulation ConfigurationTaip Command Emulation 34 AceManager PinPoint *PPIP/*PPPORT 35 AceManager PinPoint *PPGPRSR Local Connection Rev 3.0B Feb.08 100 ‐ *PGPS Sending Unsolicited Taip Messages over the Local Connection Rev 3.0B Feb.08 102 Snmp Traps Management Information Base MIB Security Level Snmp ConfigurationListening Port AceManager Change Password menu option User Name and Password Community String Snmp MIB Definition SampleTrap Destination Rev 3.0B Feb.08 107 Rev 3.0B Feb.08 108 Rev 3.0B Feb.08 109 Display Responses Product ID Info information Configuration Commands DEVICEID? =1‐255 days StatusAUTOPRL=n NETERR? Any other value Failure POWERMODE? GPS Status and Map Link AT Commands Requiring PassThru mode +++ CommonMisc Miscellaneous Dmethodd.d.d.d/ppppp or Dmethod@name/ ppppp Method= P UDP Method=T TCP Method=N Telnet DS=nOPRG=n S53=methodd.d.d.d/ppppp NETALLOWZEROIP=n DPORT=n=1‐65535 HOSTPAP=n D.d=IP address STATUSCHK=n Serial =0‐255 =2‐10 seconds =tenths of a second =1‐2545Parity=O Odd Parity=E Even Parity=N None Parity=M Mark Rev 3.0B Feb.08 126 PPPNOCARRIER=n \QnCTSE=n NUMTOIP=n S60=n S0=nS7=n =seconds =interval =0 ‐ Hh=01 Slip Hh=02 PPP Hh=03 UDP Hh=04 TCP AIP=nHOR=n MDhh DU=n Hh=33 BsapS82=n S83=n D.d=IP address of domain server DNSUPDATE=nUDPLAST=n USD=n DOMAIN=name Dynamic IPDNSUSER=d.d.d.d MODEMNAME=name IPMGRUPDATEn=mName=domain name IPMGRKEYn=key DHCPSERVER=n PPP/Ethernet D.d=local or peer IP address of the modem HOSTUID=string String=passwordPassThru HOSTPW=string =1‐255 hours String=AT commands=1‐255 minutes SMTPFROM=email Pw= passwordNETSMS2EMAIL=n =SMS/E‐mail server number Subject=message subject SMTPSEND=emailbodyEmail=email address Body=message body SMTPSUBJ=subject IPPING=n OtherDAE=n DATZ=n =1‐255 seconds D.d=IP address Name=domain nameName=domain name Port=port =1 On Host=IP address Port=TCP port DTRP=n Low Power=minutes TPORT=n VLTG=n Friends=0‐255 minutes D.d = IP address LoggingFM=n DBGIPLVL=n DBGCOMMLVL=nDBGDHCPLVL=n DBGETHLVL=n GPSn PinPoint GPSDTRI=n PPCOM1000=n RTSI=n#IG=n PGPS=n =0‐65535 hex PPLATSR=n PPINPUTEVT=nPPLATS=n PPLATSEXTRA=n =meters =1‐65535 seconds PPTCPPOLL=n PPSNFM=nPPSNFR=n PPTAIPID=nnnn UDPRGPS=n 1x/EV-DOPPTSV=n Nnnnnn=6 digit unlock code +CTA=n$QCMIP=n ~NAMLCK=nnnnnn Nam=0 Min=phone number Nam=0 Min=phone number Msid=second number 157 20070914 Connect the PinPoint-E Installing a modem driver for PinPoint-EInstall the driver Select the Modems tab Check Don’t detect my modem I will select it from a list Check Selected Ports Modem Properties Configure the driver Modem Properties Modem Creating a Dial-Up Networking PPP Connection 10 Windows Start menu Create a new network connection Select Connect to the Internet Select Set up my connection manually Rev 3.0B Feb.08 167 Rev 3.0B Feb.08 168 21 New Connection Finish Configure the DUN connection Check Show icon...when connected Rev 3.0B Feb.08 171 Select Advanced Start AceView Connecting to the Internet Using DUN Windows DUN Enable the Connection Select Dial to connect to the modem and the cellular network Start the DUN session Windows Dial-up Networking DUN Rev 3.0B Feb.08 176