OPTIONS1 Options 1 Configuration | Sterling 30RA010-055 manual

OPTIONS1 (Options 1 Configuration)

DESCRIPTION		VALUE	DEFAULT	UNITS	POINT NAME
Cooler Fluid	1	= Water	1		FLUIDTYP
	2	= Med. Brine
Minimum Load Vlv Select	No/Yes		No		MLV_FLG
Return Gas Sensor Enable	Dsable/Enable		Dsable		RGT_ENA
Motormaster Select	No/Yes		No		MTR_TYPE
Cooler Pump Control	Off/On		Off		CPC
Cooler Pump 1 Enable	No/Yes		No		PMP1_ENA
Cooler Pump 2 Enable	Dsable/Enable		Dsable		PMP2_ENA
Cooler Pmp Periodic Strt	No/Yes		No		PUMP_PST
Cooler Pump Select	0	= Automatic	0		PMP_SLCT
	1	= Pump 1
	2	= Pump 2
Cooler Pump Shutdown Dly	0 to 10		1	minutes	PUMP_DLY
Pump Changeover Hours	10 to 2000		500	hours	PMP_DLTA
EMM Module Installed	No/Yes		No		EMM_BRD

OPTIONS2 (Options 2 Configuration)

DESCRIPTION		VALUE	DEFAULT	UNITS	POINT NAME
Control Method	0	= Switch	0		CONTROL
	2	= Occupancy
	3	= SCN
Loading Sequence Select	1	= Equal Loading	1		SEQ_TYP
	2	= Staged Loading
Lead/Lag Circuit Select	0	= Automatic	0		LEAD_TYP
	1	= Circuit A Leads
	2	= Circuit B Leads
Cooling Setpoint Select	0	= Single	0		CLSP_TYP
	1	= Dual, remote switch controlled
	2	= Dual SCN occupancy
	3	= 4-20 mA input
Ramp Load Select	Enable/Dsable		Enable		RAMP_EBL
Heat Cool Select	Cool/Heat		Cool		HEATCOOL
High LCW Alert Limit	2 to 60		60.0	∆F	LCW_LMT
Minutes off time	0 to 15		0	min	DELAY
Deadband Multiplier	1.0 to 4.0		2.0		Z_GAIN
Ice Mode Enable	Enable/Dsable		Dsable		ICE_CNFG
Close Control Select	Enable/Dsable		Dsable		CLS_CTRL
Low Sound Mode Select	0	= Disabled	1		LS_MODE
	1	= Fan only
	2	= Capacity/Fans
Low Sound Start Time	00:00 to 23:59		00:00		LS_START
Low Sound End Time	00:00 to 23:59		00:00		LS_END
Low Sound Capacity Limit	0 to 100		100	%	LS_LIMIT
Enable Short Loop Gain	Enable/Dsable		Enable		SAGENABL

80

Image 80

Sterling 30RA010-055 manual OPTIONS1 Options 1 Configuration, OPTIONS2 Options 2 Configuration

Contents

SAFETY CONSIDERATIONS CONTENTS GENERAL MAJOR SYSTEM COMPONENTS Control Module CommunicationSterlco Comfort Network SCN Interface — Table 1 — Unit Sizes Table 3 — Status Switches Table 5 - SCN Communication Bus WiringTable 2 — Thermistor Designations Table 4 - Output Relays LEGEND FOR FIG. Page Page Fig. 3 — Wiring Schematic 30RA010-018 30RA010-018AQUA SNAP SEE NOTE SEE NOTE AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATICFig. 3 - Wiring Schematic 30RA010-018cont Fig. 4 - Wiring Schematic 30RA022-030 30RA022-030AQUA SNAP Fig. 4 - Wiring Schematic 30RA022-030cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATIC Fig. 5 — Wiring Schematic 30RA032-040 30RA032-040AQUA SNAP Fig. 5 — Wiring Schematic 30RA032-040cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATIC Fig. 6 — Wiring Schematic 30RA042-055 30RA042-055AQUA SNAP Fig. 6 — Wiring Schematic 30RA042-055cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATIC Fig. 7 — Main Base Board ESCAPEENTERREMOTE CONTACT SW1 OFF ENABLE OFF SW2 ON MODE Fig. 9 — Typical Space Temperature Sensor Wiring Fig. 11 - Energy Management Module CEPL130351 100/100 Fig. 12 — Deadband Multiplier Fig. 14 — 30RA Condenser Fan Sequence Fig. 13 — Operating Envelope forR-22Maneurop Compressor Cooling Set Point Select Service Test See Table 11 — Both main power and control circuit power must be onTable 8 — Control Methods and Cooling Set Points Fig. 16 — Scrolling Marquee Display Optional Factory-InstalledHydronic Package — •Cooler Pump Control CPC Configuration, OPT1 ON Fig. 17 — Dual Chiller Thermistor Location Table 9 — Marquee Display Menu Structure Table 10 — Run Status Mode and Sub-ModeDirectory SUB-MODE Table 12 - Temperature Mode and Sub-ModeDirectory Table 15 — Inputs Mode and Sub-ModeDirectory Table 13 — Pressure Mode and Sub-ModeDirectoryTable 14 — Set Point and Sub-ModeDirectory Table 16 — Outputs Mode and Sub-ModeDirectory SUB-MODEKEYPAD DISPLAY SUB-MODE KEYPADITEM DISPLAY SUB-MODE KEYPADITEM DISPLAY Table 18 — Time Clock Mode and Sub-ModeDirectory PER.3 SUB-MODE Table 20 — Alarms Mode and Sub-ModeDirectory Table 19 — Operating Mode and Sub-ModeDirectory SUB-MODE ITEMKEYPAD ENTRY DISPLAY RSET DISP Table 23 — Operating Modes Table 24 — Example of Reading and Clearing Alarms Table 25A — 4-20mA Reset Table 26B — Configuring Return Temperature Reset Fig. 18 — Standard Chilled Fluid Temperature Control — No ResetFig. 19 — Outdoor-AirTemperature Reset Fig. 20 — Space Temperature Reset Fig. 21A — 4- to 20-mADemand Limiting Fig. 21B — Cooling Set Point 4 to 20 mA TROUBLESHOOTING Table 27 — Configuring Demand Limit and fluid tubing Table 28 — TroubleshootingRecommended that system be filled with an appro Fig. 22 — Component Arrangement — 30RA010-030 FU — Fuse GND — Ground Fig. 23 — Component Arrangement — 30RA032-040 FU — Fuse GND — Ground Fig. 24 — Component Arrangement — 30RA042-055 FU — Fuse GND — Ground NOTES LEGEND Table 29 — Alarm and Alert Codes Table 29 - Alarm and Alert Codes cont Table 29 — Alarm and Alert Codes cont ALARM Table 29 — Alarm and Alert Codes cont ALARM Table 29 — Alarm and Alert Codes cont ALARM SERVICE Compressor Replacement Refer to FigTable 30 - Unit Torque Specification Electronic Components Fig. 28 — Compressor Wiring Fig. 27 — Typical Compressor Mounting — All SizesFig. 29 — Compressor Location — 30RA010-030 Fig. 30 — Compressor Location — 30RA032-055 Condenser Section and Coils Table 31 - Oil Charge Fig. 31 — 30RA Access Panels Check Refrigerant Feed ComponentsFig. 32 — Condenser-FanMounting Fig. 33 — Condenser-FanPosition Standard Fan Table 32 — Factory Settings, High-Pressure Switch FixedCompressor and Unit Protective Devices Check Unit Safeties COOLER FREEZE-UPPROTECTION TEMP TEMP For Thermistor T10 For Thermistor T10 Fig. 36 — Thermistor Connections to Main Base Board, J8 ConnectorFig. 35 — Fluid-SideTemperature Sensors T1 and T2 PROGRAMMING Mode •P51: SOFTWARE version Table 37 - Fault Codes•P50: FAULT HISTORY — Last 8 faults PARAMETERS Table 39 — Replacement Modules MAINTENANCE Minimum Loop VolumePRE-START-UP System Check Operating Limitations Standard 30RA Units OPERATION SEQUENCETable 41 — Temperature Limits for APPENDIX A SCN Tables A_UNIT General Unit ParametersCIRCADIO Circuit A Discrete Inputs/Outputs CIRCA_AN Circuit A Analog Parameters OPTIONS Unit Parameters CIRCBDIO Circuit B Discrete Inputs/OutputsCIRCB_AN Circuit B Analog Parameters ALARMDEF Alarm Definition Table DISPLAY Marquee Display SETUPDUALCHIL Dual Chiller Configuration Settings BRODEFS Broadcast POC Definition Table OPTIONS1 Options 1 Configuration OPTIONS2 Options 2 Configuration SETPOINT SCHEDOVR Timed Override SetupRESETCON Temperature Reset and Demand Limit MAINTENANCE ALARMS: Maintenance DisplayUNIT CURRMODS: Maintenance Display DUALCHIL: Maintenance Display LEARNFNS Maintenance Display LOADFACT: Maintenance Display PM-STRN Maintenance Display PM-COIL:Maintenance DisplayPM-PUMP:Maintenance Display RUNTEST: Maintenance Display VERSIONS: Maintenance Display STRTHOUR Maintenance DisplayTESTMODE: Maintenance Display WSMDEFME: Maintenance Display AND MANUAL STARTERS FACTORY SETTINGS FOR COMPRESSOR, FAN, PUMPAPPENDIX B AND MANUAL STARTERS cont FACTORY SETTINGS FOR COMPRESSOR, FAN, PUMP APPENDIX C DataPort, DataLink, BAClink Object Definition OPTIONS SETPOINT START-UPCHECKLIST FOR 30RA LIQUID CHILLER Remove and use for Job File I.Project InformationII. Preliminary Equipment Check Design Information III. Unit Start-Up Start and Operate Machine. Complete the Following CL-3 CL-4 Record Software Versions MODE — RUN STATUSCOMMENTS III.Unit Start-Upcont UNIT Configuration SettingsOPTIONS1 Options Configuration OPTIONS2 Options Configuration RSET Reset Configuration SettingsIII.Unit Start-Upcont CL-6 SLCT Setpoint and Ramp Load Configuration III.Unit Start-UpcontSETPOINT CL-7 Service Test Mode and Sub-ModeDirectory III.Unit Start-Upcont