OPTIONS2 Options Configuration, CL-6 | Sterling 30RA010-055 specs

III.Unit Start-Up (cont)

PRESS ESCAPE KEY TO DISPLAY ‘OPT1’. PRESS DOWN ARROW KEY TO DISPLAY ‘OPT2’. PRESS ENTER KEY.

RECORD CONFIGURATION INFORMATION BELOW.

OPTIONS2 (Options Configuration)

SUBMODE	ITEM	DISPLAY	DESCRIPTION	VALUE
OPT2			UNIT OPTIONS 2 CONTROLS
	CTRL	X	CONTROL METHOD
	SCNA	XXX	SCN ADDRESS
	SCNB	XXX	SCN BUS NUMBER
	BAUD	X	SCN BAUD RATE
	LOAD	X	LOADING SEQUENCE SELECT
	LLCS	X	LEAD/LAG CIRCUIT SELECT
	LCWT	XX.X ∆F	HIGH LCW ALERT LIMIT
	DELY	XX	MINUTES OFF TIME
	ICE.M	ENBL/DSBL	ICE MODE ENABLE
	CLS.C	ENBL/DSBL	CLOSE CONTROL SELECT
	LS.MD	X	LOW SOUND MODE SELECT
	LS.ST	00:00	LOW SOUND START TIME
	LS.ND	00:00	LOW SOUND END TIME
	LS.LT	XXX %	LOW SOUND CAPACITY LIMIT

RSET (Reset Configuration Settings)

SUBMODE	ITEM	DISPLAY	DESCRIPTION	VALUE
RSET			RESET COOL TEMP
	CRST	X	COOLING RESET TYPE
	MA.DG	XX.X °F	4-20 - DEGREES RESET
	RM.NO	XXX.X °F	REMOTE - NO RESET TEMP
	RM.F	XXX.X °F	REMOTE - FULL RESET TEMP
	RM.DG	XX.X °F	REMOTE - DEGREES RESET
	RT.NO	XXX.X °F	RETURN - NO RESET TEMP
	RT.F	XXX.X °F	RETURN - FULL RESET TEMP
	RT.DG	XX.X °F	RETURN - DEGREES RESET
	DMDC	X	DEMAND LIMIT SELECT
	DM20	XXX %	DEMAND LIMIT AT 20 MA
	SHNM	XXX	LOADSHED GROUP NUMBER
	SHDL	XXX %	LOADSHED DEMAND DELTA
	SHTM	XXX	MAXIMUM LOADSHED TIME
	DLS1	XXX %	DEMAND LIMIT SWITCH 1
	DLS2	XXX %	DEMAND LIMIT SWITCH 2
	LLEN	ENBL/DSBL	LEAD/LAG CHILLER ENABLE
	MSSL	SLVE/MAST	MASTER/SLAVE SELECT
	SLVA	XXX	SLAVE ADDRESS
	LLBL	X	LEAD/LAG BALANCE SELECT
	LLBD	XXX	LEAD/LAG BALANCE DELTA
	LLDY	XXX	LAG START DELAY
	PARA	YES/NO	PARALLEL CONFIGURATION

CL-6

Image 98

Sterling 30RA010-055 manual OPTIONS2 Options Configuration, RSET Reset Configuration Settings, III.Unit Start-Upcont, CL-6

Contents

SAFETY CONSIDERATIONS CONTENTS GENERAL Sterlco Comfort Network SCN Interface — MAJOR SYSTEM COMPONENTSControl Module Communication Table 1 — Unit Sizes Table 2 — Thermistor Designations Table 3 — Status SwitchesTable 5 - SCN Communication Bus Wiring Table 4 - Output Relays LEGEND FOR FIG. Page Page Fig. 3 — Wiring Schematic 30RA010-018 30RA010-018AQUA SNAP SEE NOTE SEE NOTE AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATICFig. 3 - Wiring Schematic 30RA010-018cont Fig. 4 - Wiring Schematic 30RA022-030 30RA022-030AQUA SNAP Fig. 4 - Wiring Schematic 30RA022-030cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATIC Fig. 5 — Wiring Schematic 30RA032-040 30RA032-040AQUA SNAP Fig. 5 — Wiring Schematic 30RA032-040cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATIC Fig. 6 — Wiring Schematic 30RA042-055 30RA042-055AQUA SNAP Fig. 6 — Wiring Schematic 30RA042-055cont AQUA-SNAPLOW VOLTAGE CONTROL SCHEMATIC REMOTE CONTACT SW1 OFF ENABLE OFF SW2 ON Fig. 7 — Main Base BoardESCAPEENTER MODE Fig. 9 — Typical Space Temperature Sensor Wiring Fig. 11 - Energy Management Module CEPL130351 100/100 Fig. 12 — Deadband Multiplier Fig. 14 — 30RA Condenser Fan Sequence Fig. 13 — Operating Envelope forR-22Maneurop Compressor Cooling Set Point Select Table 8 — Control Methods and Cooling Set Points Service Test See Table 11 — Both main powerand control circuit power must be on Fig. 16 — Scrolling Marquee Display Optional Factory-InstalledHydronic Package — •Cooler Pump Control CPC Configuration, OPT1 ON Fig. 17 — Dual Chiller Thermistor Location Table 9 — Marquee Display Menu Structure Table 10 — Run Status Mode and Sub-ModeDirectory SUB-MODE Table 12 - Temperature Mode and Sub-ModeDirectory Table 15 — Inputs Mode and Sub-ModeDirectory Table 13 — Pressure Mode and Sub-ModeDirectoryTable 14 — Set Point and Sub-ModeDirectory KEYPAD Table 16 — Outputs Mode and Sub-ModeDirectorySUB-MODE DISPLAY ITEM SUB-MODEKEYPAD DISPLAY ITEM SUB-MODEKEYPAD DISPLAY Table 18 — Time Clock Mode and Sub-ModeDirectory PER.3 SUB-MODE Table 20 — Alarms Mode and Sub-ModeDirectory Table 19 — Operating Mode and Sub-ModeDirectory KEYPAD ENTRY SUB-MODEITEM DISPLAY RSET DISP Table 23 — Operating Modes Table 24 — Example of Reading and Clearing Alarms Table 25A — 4-20mA Reset Table 26B — Configuring Return Temperature Reset Fig. 19 — Outdoor-AirTemperature Reset Fig. 18 — Standard Chilled FluidTemperature Control — No Reset Fig. 20 — Space Temperature Reset Fig. 21A — 4- to 20-mADemand Limiting Fig. 21B — Cooling Set Point 4 to 20 mA TROUBLESHOOTING Table 27 — Configuring Demand Limit and fluid tubing Table 28 — TroubleshootingRecommended that system be filled with an appro Fig. 22 — Component Arrangement — 30RA010-030 FU — Fuse GND — Ground Fig. 23 — Component Arrangement — 30RA032-040 FU — Fuse GND — Ground Fig. 24 — Component Arrangement — 30RA042-055 FU — Fuse GND — Ground NOTES LEGEND Table 29 — Alarm and Alert Codes Table 29 - Alarm and Alert Codes cont Table 29 — Alarm and Alert Codes cont ALARM Table 29 — Alarm and Alert Codes cont ALARM Table 29 — Alarm and Alert Codes cont ALARM Table 30 - Unit Torque Specification SERVICECompressor Replacement Refer to Fig Electronic Components Fig. 29 — Compressor Location — 30RA010-030 Fig. 28 — Compressor WiringFig. 27 — Typical Compressor Mounting — All Sizes Fig. 30 — Compressor Location — 30RA032-055 Condenser Section and Coils Table 31 - Oil Charge Fig. 32 — Condenser-FanMounting Fig. 31 — 30RA Access PanelsCheck Refrigerant Feed Components Fig. 33 — Condenser-FanPosition Standard Fan Compressor and Unit Protective Devices Table 32 — Factory Settings, High-PressureSwitch Fixed Check Unit Safeties COOLER FREEZE-UPPROTECTION TEMP TEMP For Thermistor T10 For Thermistor T10 Fig. 36 — Thermistor Connections to Main Base Board, J8 ConnectorFig. 35 — Fluid-SideTemperature Sensors T1 and T2 PROGRAMMING Mode •P51: SOFTWARE version Table 37 - Fault Codes•P50: FAULT HISTORY — Last 8 faults PARAMETERS Table 39 — Replacement Modules PRE-START-UP MAINTENANCEMinimum Loop Volume System Check Operating Limitations Standard 30RA Units OPERATION SEQUENCETable 41 — Temperature Limits for CIRCADIO Circuit A Discrete Inputs/Outputs APPENDIX ASCN Tables A_UNIT General Unit Parameters CIRCA_AN Circuit A Analog Parameters OPTIONS Unit Parameters CIRCBDIO Circuit B Discrete Inputs/OutputsCIRCB_AN Circuit B Analog Parameters DUALCHIL Dual Chiller Configuration Settings ALARMDEF Alarm Definition TableDISPLAY Marquee Display SETUP BRODEFS Broadcast POC Definition Table OPTIONS1 Options 1 Configuration OPTIONS2 Options 2 Configuration SETPOINT SCHEDOVR Timed Override SetupRESETCON Temperature Reset and Demand Limit MAINTENANCE ALARMS: Maintenance DisplayUNIT CURRMODS: Maintenance Display DUALCHIL: Maintenance Display LEARNFNS Maintenance Display LOADFACT: Maintenance Display PM-STRN Maintenance Display PM-COIL:Maintenance DisplayPM-PUMP:Maintenance Display RUNTEST: Maintenance Display VERSIONS: Maintenance Display STRTHOUR Maintenance DisplayTESTMODE: Maintenance Display WSMDEFME: Maintenance Display AND MANUAL STARTERS FACTORY SETTINGS FOR COMPRESSOR, FAN, PUMPAPPENDIX B AND MANUAL STARTERS cont FACTORY SETTINGS FOR COMPRESSOR, FAN, PUMP APPENDIX C DataPort, DataLink, BAClink Object Definition OPTIONS SETPOINT II. Preliminary Equipment Check START-UPCHECKLIST FOR 30RA LIQUID CHILLERRemove and use for Job File I.Project Information Design Information III. Unit Start-Up Start and Operate Machine. Complete the Following CL-3 CL-4 Record Software Versions MODE — RUN STATUSCOMMENTS III.Unit Start-Upcont UNIT Configuration SettingsOPTIONS1 Options Configuration III.Unit Start-Upcont OPTIONS2 Options ConfigurationRSET Reset Configuration Settings CL-6 SETPOINT SLCT Setpoint and Ramp Load ConfigurationIII.Unit Start-Upcont CL-7 Service Test Mode and Sub-ModeDirectory III.Unit Start-Upcont