Mosquito NR (Mosquito noise reduction)

Mosquito noise is a type of noise that appears along edges of compression artifacts. Use this feature to adjust the mosquito noise reduction level.

Choices: Off, Low, Medium, HighBlock NR (Block noise reduction)

Block noise is often caused when the bitrate is too low to accurately encode the video. Use this feature to adjust the block noise reduction level.

Control range: 0 to 50Detail Enhancement (Detail enhancement)Use this feature to adjust finesses of images. Control range: 0 to 50Edge Enhancement (Edge enhancement)Use this feature to adjust sharpness of images. Control range: 0 to 50Brightness (Brightness)Use this feature to adjust brightness of images. Control range: -50 to 50

Initial setting: 0

Contrast (Contrast)Use this feature to adjust contrast of images. Control range: -50 to 50

Initial setting: 0

Saturation (Saturation)Use this feature to adjust saturation of images. Control range: -50 to 50

Initial setting: 0

Setup (HDMI)

Use this feature to set the HDMI functions or check the information about the video monitors connected to the HDMI OUT jacks.

Standby Through (Standby through)Mode (Standby through mode)

Use this feature whether this unit allows the HDMI signals input at the HDMI IN jacks to pass thorough this unit when this unit is in the standby mode. You can also designate an HDMI IN jack and HDMI OUT jack(s) that accept the signals when “Mode” is set to “Fix” and this unit is in the standby mode.

Choice

Functions

 

 

Off

Disables the HDMI standby through feature.

 

HDMI signals do not pass through this unit if

 

this unit is in the standby mode.

 

 

Last

HDMI signals pass through this unit (only from

 

the HDMI IN jack to the HDMI OUT jack(s)

 

used when this unit is set to the standby mode)

 

even when this unit is in the standby mode.

 

 

 

Graphical user interface (GUI) menu

 

 

Choice

Functions

 

 

Fix

HDMI signals pass through this unit (from the

 

HDMI IN jack specified in “Input” to the HDMI

 

OUT jack(s) specified in “Output”) even when

 

this unit is in the standby mode.

 

 

Note

When “Mode” is set to “Last” or “Fix”, the amount of power consumption in the standby mode increases.

Input (HDMI IN jack select)

Use this feature to select an HDMI IN jack that accepts HDMI signals when this unit is in the standby mode.

Note

This setting is available only when “Mode” is set to “Fix”.

Choice

HDMI IN jack

 

 

IN1

HDMI IN1 (BD/HD DVD) jack

 

 

IN2

HDMI IN2 (DVD) jack

 

 

IN3

HDMI IN3 (CBL/SAT) jack

 

 

IN4

HDMI IN4 (DVR) jack

 

 

Front

HDMI IN (VIDEO AUX) jack

 

 

Output (HDMI OUT jack select)

Use this feature to select HDMI OUT jack(s) that output HDMI signals when this unit is in the standby mode.

Note

This setting is available only when “Mode” is set to “Fix”.

Choice

HDMI IN jack

 

 

OUT1 + 2

HDMI OUT 1 and HDMI OUT 2 jacks

 

 

OUT1

HDMI OUT 1 jack

 

 

OUT2

HDMI OUT 2 jack

 

 

Audio Output (HDMI audio output)

Use this feature to select whether to play back HDMI audio signals on this unit or on another HDMI component connected to the HDMI OUT jacks on the rear panel of this unit.

Choice

Functions

 

 

Amp

Outputs HDMI audio signals at the speakers

 

connected to this unit.

 

 

TV

Outputs HDMI audio signals at the speakers of

 

the TV connected to this unit. The speakers

 

connected to this unit are muted.

 

 

Amp + TV

Outputs HDMI audio signals at the speakers

 

connected to this unit and speakers of the TV

 

connected to this unit.

 

 

y

If “Audio Output” is set to “TV” or “Amp + TV”, available audio signals vary depending on the specification of the connected video monitor.

OPERATION

ADVANCED

 

 

101 En