Troubleshooting

 

 

 

 

Problem

Cause

Remedy

See

page

 

 

 

No sound is heard

“Bass Out” in “Configuration” is set to

Set “Bass Out” to “SWFR” or “Front + SWFR”.

94

from the subwoofer.

“Front” when a Dolby Digital or DTS

 

 

 

signal is being played.

 

 

 

 

 

 

 

“Bass Out” in “Configuration” is set to

Set “Bass Out” to “Front + SWFR”.

94

 

“SWFR” or “Front” when a 2-channel

 

 

 

source is being played.

 

 

 

 

 

 

 

The source does not contain low-

 

 

 

frequency signals.

 

 

 

 

 

 

No sound is heard

“Surround Back” in “Configuration” is set

Check whether “Surround” is set to “Small” or

93, 93

from the surround

to “None”.

“Large” and configure “Surround Back” properly.

back speakers.

While this unit is in the CINEMA DSP 3D mode, no sound is output at the surround back speakers.

The audio input sources cannot be played in the desired digital audio signal format (Desired input source indicator or decoder indicator in the front panel display does not light up).

The connected component is not set to

Make an appropriate setting following the operating

—

output the desired digital audio signals.

instructions for your component.

 

 

 

 

Audio input jack select is set to

Set the audio input jack select to “AUTO”.

43

“ANALOG”.

 

 

A humming sound is

Incorrect cable connections.

Connect the audio cables firmly. If the problem

—

heard.

 

persists, the cables may be defective.

 

 

 

 

 

 

No connection from the turntable to the

Connect the grounding cable of the turntable to the

26

 

GND terminal.

GND terminal of this unit.

 

 

 

 

 

The volume level is

The record is being played on a turntable

Connect your turntable to this unit through an MC-

26

low while a record is

with an MC cartridge.

head amplifier.

 

being played.

 

 

 

 

 

 

 

The volume level

The component connected to the AUDIO

Turn on the power of the component.

—

cannot be increased,

OUT (REC) jacks of this unit is turned

 

 

or the sound is

off.

 

 

distorted.

 

 

 

 

 

 

 

A source cannot be

The audio source connected to the MULTI

 

 

recorded by the

CH INPUT jacks of this unit cannot be

 

 

recording component.

recorded.

 

 

 

 

 

 

 

A given input source is not output at the

Connect the recording component to another channel

25

 

same output channel (e.g. DVR IN to

that is not being used for connecting the source

 

 

DVR OUT).

component.

 

 

 

 

 

 

While “Zone 4” is set to “ON”, no signal

Set “Zone 4” to “OFF”.

127

 

is output at the analog AUDIO OUT

 

 

 

(DVR, VCR, MD/CD-R) and OPTICAL

 

 

 

(MD/CD-R) jacks.

 

 

 

 

 

 

 

You are trying to record a DTS source.

Make a setting so that the analog signal will be output

25

 

(DTS signal is a digital bitstream.

from your DTS-compatible player and then connect

 

 

Attempting to record the DTS bitstream

the DTS-compatible player to the AUDIO IN jacks

 

 

digitally will result in noise being

while the recording component is connected to the

 

 

recorded.)

analog AUDIO OUT (DVR, VCR or MD/CD-R)

 

 

 

jacks.

 

 

 

 

 

INFORMATION

ADDITIONAL

 

 

135 En