Error Conditions and Warnings | Zebra Technologies Z6Mplus specs

Troubleshooting

LCD Error Conditions and Warnings

Table 12 • Error Conditions and Warnings (Continued)

Error

Potential Problem

Recommended Solution

OUT OF MEMORY* *There is not enough memory to perform the function shown on the second line of the error message.

Insufficient DRAM for the label length, downloaded fonts/graphics, and images.

Ensure that the device, such as FLASH memory or PCMCIA card, is installed and not write protected or full.

Ensure that the data is not directed to a device that is not installed or available.

90

Z4Mplus/Z6Mplus User Guide

13163L Rev. 3 5/20/2004

Image 108

Zebra Technologies Z6Mplus manual Error Conditions and Warnings

Contents

User Guide Customer Order # 13163L Manufacturer 13163LB Rev Contents Printer Setup Configuration Index Proprietary Statement Product ImprovementsFCC Compliance Statement Canadian DOC Compliance Statement Liability DisclaimerLimitation of Liability Declaration of Conformity Viii Z4Mplus/Z6Mplus User Guide 13163L Rev 5/20/2004 Warranty Information Effective December 30Printers and Related Hardware Products Printers Related Hardware Items Supplies Products Repair Services Warranty Exclusions & Conditions Statement Xii Z4Mplus/Z6Mplus User Guide 13163L Rev 5/20/2004 Contents Preface Contacts SupportZebra Technologies Europe Limited US Phone Number +1 UK/International Phone Number +44 0 1494 Document Conventions Ztools Related Documents Example of an Illustration with Callouts Introduction External View External View Front Panel Front Panel Controls and LEDs LCD Display Settings Print Mode Options Print Modes Printer Media Compartment Media Compartment Printer Setup Before You Begin Unpack and Inspect the Printer Report DamageStorage Select a Site for the Printer Select a SurfaceProvide Proper Operating Conditions Allow Proper Space Connect the Printer to a Power Source Power Cord Specifications International Safety Organization Marks Select a Communication Interface Optional Print Servers Communicating Using a Parallel Port Cable Requirements Types of Media Selecting Media Non-Continuous Media Continuous Media When to Use Ribbon RibbonRibbon Width Coated Side of Ribbon To perform an adhesive test, complete these steps To perform a ribbon scratch test, complete these steps If the ribbon Then Printer Setup Printer Operation Front Panel Front Panel Keys Front Panel Keys Front Panel Lights Front Panel Lights Tear-Off Mode Load Roll MediaTo load media in Tear-Off Mode, complete these steps Cutter Mode To load media in Cutter-Off Mode, complete these steps Printer Operation Peel-Off Mode To load media in Peel-Off Mode, complete these steps Printer Operation Liner Take-Up Mode To load media in Liner Take-Up Mode, complete these steps Liner Take-Up Spindle Liner Removal Rewind/Peel-Off Mode To load media in Rewind/Peel-Off Mode, complete these steps Liner Removal Rewind Mode To load media in Rewind Mode, complete these steps Media Removal Adjust Media Alignment for Rewind Option Rewind Option Adjustment Dial Load Fanfold Media Loading Fanfold Media To load fanfold media, complete these steps Load the Ribbon To load ribbon, complete these steps Remove the Ribbon To remove used ribbon, complete these steps Calibrate the Printer Auto CalibrationManual Calibration Print a Configuration Label To print a configuration label, complete these steps Go to Configuration on Print a Network Configuration Label Network Configuration Label Adjust Printhead Pressure Z4Mplus Printhead Pressure Z6Mplus Printhead Pressure Install Memory Card To install the Pcmcia memory card, complete these steps Configuration Enter Configuration Mode To enter configuration mode, complete these stepsOverview Exit Configuration Mode To exit configuration mode, complete these steps Change Password-Protected Parameters To enter a password, complete these steps Basic Configuration To perform basic a configuration, complete these stepsYes No 1. Press Select Continue with Select Media Type Continue with Select Sensor Type Yes 1. Continue with Save Changes and Exit Configuration and Calibration LCD Displays R K N E S SPrinter Parameters and Other LCD Displays Sheet 1 Printer Parameters and Other LCD Displays Sheet 2 Setting Print Width Print WidthPrinter Parameters and Other LCD Displays Sheet 3 Sensor Select Selecting Sensor List Setup List FontsList List Images List ALL Format CardPrinter Parameters and Other LCD Displays Sheet 5 Printer Parameters and Other LCD Displays Sheet 6 Init Flash MEM Initialize Flash Memory Media and Ribbon Printer Parameters and Other LCD Displays Sheet 7Media and Ribbon Sensor Calibration Manual Calibration Serial Comm BaudData Bits Printer Parameters and Other LCD Displays Sheet 8 R I T Y HostHandshake Protocol Communication Diagnostics Test Printout Printer Parameters and Other LCD Displays Sheet 10 Printer Parameters and Other LCD Displays Sheet 11 Control Prefix Control Prefix CharacterFormat Prefix Format Prefix Character Delimiter Char Delimiter Character ZPL Mode MediaHead Close Printer Parameters and Other LCD Displays Sheet 12 C K F E E D Label TOPLeft Position Printer Parameters and Other LCD Displays Sheet 13 WEB S Media S Ribbon S . Take Label Media LED Ribbon LED Idle DisplayRTC Date Printer Parameters and Other LCD Displays Sheet 14 Password RTC TimeLevel Language ZebraNet Wired and Wireless Print Server LCD Displays Leap Mode 3,4 Encryption Configuration Routine Care Adjustments Cleaning Procedures Clean the ExteriorClean the Interior Recommended Cleaning Schedule Clean the Printhead and Platen Roller Cleaning the Printhead and Platen Roller Routine Care and Adjustments Clean the Sensors Cleaning the Sensors Clean the Rewind Option To clean the Rewind option, complete these steps Clean the Peel-Off Assembly Clean the Cutter Module To clean the cutter module, complete these steps Fuse Replacement LubricationTo replace the fuse, complete these steps Adjust the Reflective Sensor Position the Label Sensor To adjust the reflective sensor, complete these steps Select the Transmissive Sensor Location of Transmissive Sensors Troubleshooting Content LCD Error Conditions and Warnings Error Conditions and WarningsRibbon OUT Paper OUT Head Open HeadHead Under Temp Cutter JAM Error Conditions and Warnings Print Quality Problems Print Quality Problems and Solutions Calibration Problems Calibration Problems and Solutions Communication Problems Communication Problems and Solutions Miscellaneous Problems and Solutions MiscellaneousPrinter is displaying a Language that I cannot read Printer Diagnostics Power-On Self Test Cancel Self Test To perform the Cancel Self Test, complete these steps Pause Self Test To perform the Pause Self Test, complete these stepsPause Feed Self Test To perform the Feed Self Test, complete these steps Communication Diagnostics Test Feed and Pause Self TestTo perform a Feed and Pause self test, complete these steps Loading Factory Defaults To load the factory defaults, complete these steps Data Connections Hardware Control Signal Descriptions Serial Data Port Serial Data Connector Pin Configuration RS-232 Serial Data Port RS-232 Interface Connections RS-232 Interconnections Using a DB-25 Cable RS-422/RS-485 Interconnections Parallel Cable Pin Configuration Parallel Data PortParallel Cabling Requirements Parallel Port Interconnections 108 Specifications General Specifications Z4Mplus and Z6Mplus General Specifications Printing Specifications Z4Mplus and Z6Mplus Printing Specifications Media Specifications Z4Mplus and Z6Mplus Media Specifications Ribbon Specifications Z4Mplus and Z6Mplus Ribbon Specifications Printer Options Z4Mplus and Z6Mplus Options Zebra Programming Language ZPL II Features UPC/EAN Supported Bar Codes Supported Bar Codes Index Index Out of Memory message 120 13163L Rev 5/20/2004 Z4Mplus/Z6Mplus User Guide 121 122 Page Customer Order # 13163LB Manufacturer 13163LB Rev ZIH Corp