Zenoah BCX2601DL manual OP9

Page 40

 

English

 

Français

 

 

8. Operation

8. Fonctionnement

 

 

 

 

SET UP

INSTALLATION

OP9

(1)

(2)

OP10

1.Detach the line head assembly completely. (OP9)

2.Put the blade making the marked side face the holder, put the outer holders, and fasten the blade by the washer and the blade bolt. (OP9)

(1)Cover 6420-13280

(2)Holder 6019-13250

CUTTING METHOD

(a)Use the front left side cutting.

(b)Guide the blade from your right to left with it tilted slightly to your left. (OP10)

(c)When mowing a wide area, start working from your left end to avoid interference of cut grass.

(d)The blade may be seized by weeds if the engine speed is too low, or the blade cuts too deep into weeds. Adjust the engine speed and cutting depth according to the condition of object.

WARNING

If the grass or other object gets caught in the blade, or if the unit starts to shake or vibrate, turn off the engine and check the whole unit. Change the blade if it has been damaged.

Turn off the engine and make sure the blade has completely stop before checking the blade, and removing any object got caught in.

1.Détacher complètement l'assemblage de la tête de ligne(OP9).

2.Mettre la lame de façon à ce que son côté marqué soit en face du support, mettre les supports extérieurs et fixer la lame entre la rondelle et le verrou (OP9).

(1)gaine 6420-13280

(2)Support 6019-13250

METHODE DE COUPE

(a)Couper avec le côté gauche et avant de la lame.

(b)Guider la lame de droite à gauche en l’inclinant légèrement sur la gauche (OP10).

(c)Lors de la coupe d’une zone de grande largeur, commencer le travail par la gauche pour ne pas être gêné par l’herbe déjà coupée.

(d)La lame peut être bloquée par l’herbe si la vitesse du moteur est trop lente ou si elle est enfoncée trop profondément et rapidement dans l’herbe. Régler la vitesse du moteur et l’engagement de la lame en fonction du travail à effectuer.

AVERTISSEMENT

Si de l’herbe ou tout autre objet se coince dans la lame ou si la machine se met à vibrer, arrêter aussitôt le

moteur et vérifier la débroussailleuse. Changer la lame si elle est endommagée.

Arrêter le moteur et attendre que la lame soit complètement à l’arrêt avant de la vérifier et d’enlever le moindre objet coincé.

WARNING

CONTROLLING BLADE BOUNCE

Kick out can cause serious personal injury. Carefully study this section. It is important that you understand what causes kick out, how you can reduce the chance of kick out and how you can remain in control of the unit if kick out does occur.

1. What causes kick out:

Kick out can occur when the moving blade contacts an object that it cannot cut. This contact causes the blade to stop for an instant and then suddenly move or ”bounce” away from the object that was hit. The operator can lose control of the unit and the blade can cause serious personal injury to the operator or any person nearby if the

AVERTISSEMENT

CONTROLE DES COUPS DE RECUL

• Les coups de recul peuvent causer de sérieuses blessures. Etudier attentivement cette section. Il est important de comprendre la cause des coups de recul, de savoir comment réduire leur éventualité et de conserver le contrôle de la machine dans ces circonstances.

1. Cause des coups de recul :

Les coups de recul se produisent lorsque la lame rencontre un objet qu’elle ne peut couper. Ce genre de contact arrête la lame pendant un instant puis rebondit soudainement en se libérant de l’objet du contact.

L’opérateur peut perdre le contrôle de

40

Image 40
Contents BCX2601DL English Français Deutsch Italiano Español Page Risk of Damaging Hearing Hörschaden RisikoRischio DI Danno Uditivo Riesgo DE Daño AuditivoContents Tables des matieres Inhalt Indice Contenido Parts location Emplacement des pieces Parachispas Fiche technique SpecificationsBCX2601DL Dati tecnici Technische DatenEspecificaciohes Symbols on the machine Symboles utilises sur la Machine EmplacementEtiquettes d’avertissement Machine Sur la machinePosizione PosiciónFor safe operation Consignes de securite Working ConditionWorking Circumstance Conditions DE TravailArbeitsbedingung ArbeitsumstandCondizioni Lavorative Circostanze LavorativeWorking Plan Before Starting the EnginePlan DE Travail LA MachinePiano DI Lavoro ArbeitsplanPlan DE Trabajo Starting the Engine Demarrage DU MoteurAvvertimento Advertencia DEN Motor StartenAccensione DEL Motore Arranque DEL MotorUsing the Product MaintenanceIf Someone Comes Utilisation DE LA MachineBenutzung DES Produktes Falls Sich Jemand NähertWartung Utilizzo DEL ProdottoCheck ok Handling FuelRefill after cooling the engine Komatsu ZenoahPrüfung in Ordnung Controllo OK Comprobación correctaCon esta máquina Nachfüllen nachdem der Motor abgekühlt istTransportation TransportTrasporto TransporteSet up Assemblage SE1SE2 SE3 SE4EIN Schneidekopf Installieren SE3 Zusammenbau Impostazione MontajeNstallazione Dello Strumento DA Taglio SE3 Instalación DEL Cabezal Cortador SE3Recommended OIL Type Type D’HUILE Recommande Type ’CARBURANT RecommandeOil and Fuel Huile et carburant Recommended Fuel TypeÖl und Kraftstoff Olio e carburante Aceite y combustible Warnung Avvertimento AdvertenciaOil and Fuel Huile et carburant Verwendung VON Vermischten Kraftstoffen Verwendung VON KraftstoffzusätzenUtilizzo DI Miscele DI Carburante Utilizzo DI Additivi NEL CarburanteOperation Fonctionnement OP1OP2 OP3 Starting Engine Mise EN Marche DU MoteurBetrieb Funzionamento Uso Starten DES Motors Avviamento DEL Motore Arranque DEL MotorOperation Fonctionnement OP4Betrieb Funzionamento Uso OP5 OP6Utilización DEL Cabezal DE Línea Gras UND Unkraut SchneidenPER Tagliare L’ERBA E Erbaccia Desbroce DE Hierbas Y MalezaAdjusting the Line Length OP7 OP8Metal Blade Usage Reglage DE LA Longeur DU FIL DE CoupeWarnung Avvertimento OP9 Installazione EinrichtungSchneidemethode Metodo PER TagliareHow you can reduce the chance of kick out How you can maintain the best controlComment réduire l’éventualité des coups de recul Comment conserver le meilleur contrôle de la machineWie Auslösung vermieden werden kann Wie Sie die Kontrolle aufrecht erhalten könnenTagliate solo dell’erbaccia fibrosa Per mantenere il controllo in ogni momentoMaintenance Chart MaintenaceEntretien Tableau D’ENTRETIENWartung ManutenzioneMantenimiento Tabla DE MantenimientoPage MA1 MA2 Maintenace EntretienMA3 MA4 MA5 Wartung Manutenzione Mantenimiento MA6 MA7 MA8 AIR FilterOIL Level Filtre a AIRLuftfilter Filtro DELL’ARIAFiltro DE Aire Ölstand PrüfenMA9 Oil Fill Plug/Dipstick Ring Top of DipstickChanging the OIL Changer l’huile de la manière suivanteWartung Manutenzione Mantenimiento ÖL WechselnCambio DELL’OLIO Cambio DE AceiteFeeler gauge Rocker arm Adjusting nut Gasket Screws to remove Screws to loosenRocker arm cover Vis à retirer Vis à desserrerPrüfung / Einstellung DES Ventils FÜR Steuerhebelspiel Spark Plug Filtre a Carburant Fuel FilterBougie D’ALLUMAGE Kraftstoffilter Filtro DEL Carburante Filtro DE Combustible ZündkerzeCandela BujíaTightening Torque MufflerSpark Arrester MA18 Gear Case MA19Zugelassene Zündkerze IST Eine Champion RDZ19H AnziehmomentDämpfer LA Candela Specificata DA Usare È QuellaMaintenace Entretien Intake AIR Cooling Vent Ouïe DU Refroidissement PARCylinder Intake air cooling vent back Cylindre Ouïe d’entrée d’air de refroidissement arrièreED Altre Procedure DI Betriebsstunden Manutenzione DA EffettuareOgni 100 ORE D’UTILIZZO Cada 100 Horas DE USOCleaning and Storage Nettoyage et Rangement Cleaning NettoyageStorage RangementReinigung und Lagerung Pulizia e Custodia Reinigung Pulizia LimpiezaLagerung CustodiaTroubleshooting guide Problem Cause ActionProbleme Cause Action Guide de localisation des pannesProblem Ursache Massnahme FehlersucheProblema Causa Massnahme Localizzazione dei guasti11. Guía de localización y solución de problemas Problema Causa SoluciónPage Limited warranty Garantie limitée Garantiebestimmungen Garanzia limitata Garantía limitada