Lantronix MSS manual Command Reference

Page 10

2: Command Reference

This chapter describes all commands that can be used with the MSS. The commands are listed in alphabetical order, excluding the Ports and Server parameters, which apply only to the MSS4. For example, Change Server Bootgateway is considered the same command as Change Bootgateway and is alphabetized according to the latter.

Commands that configure the MSS serial ports will not affect a dedicated console port unless explicitly stated in the individual command description.,

Some commands can be used with environment strings, which are discussed in detail in Appendix B.

The following items are provided in the description of each command.

The command’s full syntax, shown in diagram form. See Command Syntax on page 1-1for more information on the command syntax.

Any restrictions on the command, such as whether you must be the privileged user to use it

Potential errors that may be encountered when using the command

Default settings, where applicable

Examples of the command, where applicable

Cross-references to related commands

2-1

Image 10
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Backward Change 80211 EnabledChange Defaults Change 80211 AntennaRestrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPortChange Buffering DefaultsNone See AlsoDefaults Bytes Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Secondary Change Signal CheckChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect ParametersusernameHostlist ForwardParameterskeyword Show Hostlist command Initialize78 LAT ParametersDelayParametersserviceName Logout PortResume NetstatPing Parametershostname84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show NetWare Show HostlistShow IPsecurity Show NodesShow Server Show PortsShow RS485 ParametersAllParametersBootparams Show ServicesShow Session Show Version Show SnmpShow Users SourceTelnet 100 SPXParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationAvailable Strings UsageMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Introduction Error BitsLeftmost Number 04000000 1000000008000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3