Lantronix MSS manual Backward, Change 80211 Enabled

Page 11

Command Reference

Backward

2.1 Backward

BACKWARD

Moves the user to the previous session when entered in Local mode.

See Also

Change Backward Switch, page 2-14; Show Session, page 2-66.

2.2 Change 80211

Note: The Change 80211 Reset command must be entered after any 802.11 configuration command is issued. The changes made by the configuration commands will not take effect until after the Reset command is used. The Change

802.11Enabled/Disabled command requires a reboot before the change will take effect.

2.2.1Change 80211 Enabled

CHANGE 80211

ENABLED

 

DISABLED

When 802.11 is enabled, the MSS checks for a compatible 802.11 wireless Ethernet PC card at startup and, if one is present, uses the card instead of a wired Ethernet port. If no valid PC card is detected at startup, the MSS uses the 10/100BASE-T (or, for the MSS4, the 100BASE-FX) network connection.

When 802.11 is disabled, the MSS will ignore an installed 802.11 card and will only look for a compatible wired Ethernet connection.

You must reboot the MSS before those changes will take place.

Restrictions

Requires privileged user status.

Only applies to the MSS-VIA and certain MSS4 models. For the MSS4, only one 802.11 card can be installed at a time. The card can be installed in either slot of the MSS4.

ParametersEnabled

Prompts the MSS to check for a compatible 802.11 wireless Ethernet networking PC card at startup. If one is present, wireless networking will be used instead of the wired Ethernet connection. You must reboot the MSS after entering this command.

Disabled

Prompts the MSS to only look for a compatible 10/100BASE-T (or, for the MSS4, the 100BASE-FX) wired Ethernet connection at startup. You must reboot the MSS after entering this command.

2-2

Image 11
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change Change 80211 EnabledBackward Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Session Limit Change Signal CheckChange Secondary Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerParameterskeyword ForwardHostlist Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Session Show ServicesParametersBootparams Source Show SnmpShow Users Show VersionParametersSAPname 100 SPXTelnet Zero TestFull Contact Information Problem Report ProcedureMultiple Strings UsageAvailable Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Leftmost Number Error BitsIntroduction 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68