Lantronix Complete Guide to Configuring Your Network Card with MSS4

Page 81

Environment Strings

 

Usage Examples

 

 

Table B-1:Environment Strings

 

 

 

 

 

R

Rlogin protocol (sets port number to 513 if not already set)

 

 

T

TCP mode (raw uninterpreted data stream)

 

 

U

UDP mode (the default UDP socket is 4096)

 

 

S

Specifies session mode. Only valid with U.

 

 

xxxx

Timeout value in seconds, up to 3600 (1 hour). Only valid

 

 

 

with :S

 

 

Y

Encrypted mode (raw TCP socket that encrypts all data

 

 

 

using a 56-bit key)

 

 

LD=port#

Sets the LAT destination port to port#

 

 

LN=node#

Sets the target LAT node to node#

 

 

 

 

 

B.2.1 Usage Examples

These examples should illustrate the proper usage of the above environment strings.

2.2.1.1 nnnn

Sets a socket number. For TCP and UDP connections only. The most common socket numbers are 7000 (the MSS remote console port), 200x (for Telnet IAC interpretation), and 300x (for raw TCP/IP), where x is the number of the desired serial port.

Examples% telnet 192.0.1.88:7000

(connects to the remote console port of the specified host)

% telnet 192.0.1.66:3001

(forms a raw TCP/IP connection to the MSS serial console port)

Local> TELNET 192.0.1.45:2003

(forms a connection with Telnet IAC interpretation to the third serial port of an MSS4)

See Also

Your MSS Installation Guide for more information on socket connections

2.2.1.2 +C and -C

+C specifies CR to CRLF. -C specifies CR to LF.

ExamplesLocal>> CHANGE PREFERRED TELNET 192.0.1.3:+C

2.2.1.3 +D and -D

+D sets Backspace mode. -D sets Delete mode.

Examples% telnet 192.0.1.5:-D

2.2.1.4 +E and -E

+E sets Local Echo mode. -E sets Remote Echo mode.

Examples% telnet 192.0.1.48:+E

B-2

Image 81
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change 80211 Enabled BackwardChange Change 80211 Antenna DefaultsRestrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address ParametersExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchDefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPortDefaults Bytes DefaultsNone See AlsoChange Buffering Change CharsizeChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Signal Check Change SecondaryChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger ParametersusernameForward HostlistParameterskeyword Initialize Show Hostlist commandParametersserviceName ParametersDelay78 LAT Logout PortPing NetstatResume ParametershostnameRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show IPsecurity Show HostlistShow NetWare Show NodesShow RS485 Show PortsShow Server ParametersAllShow Services ParametersBootparamsShow Session Show Users Show SnmpShow Version Source100 SPX TelnetParametersSAPname Zero TestFull Contact Information Problem Report ProcedureUsage Available StringsMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Error Bits IntroductionLeftmost Number 08000000 1000000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68