Lantronix MSS manual Change 80211 Fragmentation, Change 80211 MAC Address, Errors, Parameters

Page 14

Command Reference

Change 80211

Errors

If you enter a command that is not applicable to the 802.11 card currently in

 

use, you will receive an Error message.

Parameters

name

 

Enter a string of up to 32 characters. If the string contains lowercase letters or

 

non-alphanumerics, it may need to be enclosed in double-quotes to be

 

processed properly.

 

None

 

If no ESSID string is set, the MSS will communicate with whichever Access

 

Point (AP) gives the strongest signal, regardless of ESS association. Setting the

 

ESSID to none allows the MSS to associate with any AP within range.

Defaults

ESSID=None

See Also

Show 80211, page 2-63

2.2.5 Change 80211 Fragmentation

CHANGE 80211 FRAGMENTATION num

Changes the fragmentation threshold.

Any configuration changes you make will not take place until you issue the Change 80211 Reset command.

Restrictions

Requires privileged user status.

 

Only applies to the MSS-VIA and certain MSS4 models.

Errors

If you enter a command that is not applicable to the 802.11 card currently in

 

use, you will receive an Error message.

Parameters

num

 

Enter an integer between 256 and 2346 to change the fragmentation threshold.

Defaults

2346

See Also

Show 80211, page 2-63

2.2.6 Change 80211 MAC Address

CARD

CHANGE 80211 MACADDRESS    MSS

Configures which of the two available MAC addresses the MSS will use on the network—its own or that of the attached 802.11 wireless networking PC card. The MSS MAC address, which is the same as its hardware address, is printed on bottom label of the MSS.

Any configuration changes you make will not take place until you issue the Change 80211 Reset command.

2-5

Image 14
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change Change 80211 EnabledBackward Defaults Change 80211 AntennaRestrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPortChange Buffering DefaultsNone See AlsoDefaults Bytes Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Session Limit Change Signal CheckChange Secondary Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect ParametersusernameParameterskeyword ForwardHostlist Show Hostlist command Initialize78 LAT ParametersDelayParametersserviceName Logout PortResume NetstatPing ParametershostnameParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show NetWare Show HostlistShow IPsecurity Show NodesShow Server Show PortsShow RS485 ParametersAllShow Session Show ServicesParametersBootparams Show Version Show SnmpShow Users SourceParametersSAPname 100 SPXTelnet Test ZeroProblem Report Procedure Full Contact InformationMultiple Strings UsageAvailable Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Leftmost Number Error BitsIntroduction 04000000 1000000008000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3