Lantronix MSS manual Change DSRLogout, Change DTRWait

Page 31

Command Reference

Change DSRLogout

2.16 Change DSRLogout

DISABLED

CHANGE PORT PortList DSRLOGOUT   ENABLED

If DSRLogout is enabled, the specified port will be logged out when its DSR signal is de-asserted. This logout usually happens only when the attached device is turned off or disconnected. The feature can be used to keep users from switching physical terminal lines to access other sessions. Open connections will be closed before logout.

Restrictions

Requires privileged user status.

 

Does not apply to the MSS485.

Errors

Modem Control must be disabled to use DSRLogout. Modem Control implies

 

DSRLogout.

Parameters

Port

 

MSS4 only. Specifies a particular port or group of ports.

Note:

In the absence of the PortList parameter, the configuration will affect the MSS4’s

 

current port only.

 

PortList

 

Specify a particular port or group of ports. Port numbers are specified with

 

integers between 1 and 4, and should be separated with commas (for lists) or

 

dashes (for ranges).

Defaults

Disabled

See Also

Change Modem Control, page 2-31.

2.17 Change DTRWait

DISABLED

CHANGE PORT PortList DTRWAIT   ENABLED

If enabled, the MSS will not assert the DTR signal on the specified serial port until a user logs into the port, or until a network connection is made to the port.

Restrictions

Requires privileged user status.

 

Does not apply to the MSS485.

Parameters

Note:

Port

MSS4 only. Specifies a particular port or group of ports.

In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

2-22

Image 31
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Backward Change 80211 EnabledChange Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerHostlist ForwardParameterskeyword Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing Resume84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerParametersBootparams Show ServicesShow Session Source Show SnmpShow Users Show VersionTelnet 100 SPXParametersSAPname Zero TestFull Contact Information Problem Report ProcedureAvailable Strings UsageMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Introduction Error BitsLeftmost Number 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68