Lantronix MSS manual Change LAT Groups, Change LAT Identification, Change Loadhost

Page 38

Command Reference

 

 

Change LAT Groups

2.27 Change LAT Groups

 

 

 

 

 

 

ALL

 

 

 

 

 

 

 

CHANGE LAT GROUPS

groupList

 

 

 

 

 

NONE

 

 

 

 

 

 

Specifies the LAT service groups to which the MSS can connect. Groups are numbered from 0 to 255.

Restrictions

Requires privileged user status.

Errors

The MSSLite, MSS4, and the MSS-VIA do not support LAT.

Parameters

groupList

 

Specify a list of groups to replace the current list. Use commas to separate

 

group numbers, and use hyphens to separate ranges.

Defaults

0 (group zero)

Examples

CHANGE LAT GROUPS 17,21-28,118-211,220

2.28 Change LAT Identification

CHANGE LAT IDENTIFICATION identString

Sets the text string that identifies the MSS on LAT networks.

Restrictions

Requires privileged user status.

Errors

The MSSLite, MSS4, and the MSS-VIA do not support LAT.

Parameters

identString

 

Enter a string of 40 or fewer characters. Enclose the string in quotes if it

 

contains lower-case letters, spaces, or punctuation.

2.29 Change Loadhost

CHANGE SERVER SECONDARY LOADHOST IPaddress

Specifies the TCP/IP host from which the MSS requests its runtime code.

Restrictions

Requires privileged user status.

ParametersServer

MSS4 only.

2-29

Image 38
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change Change 80211 EnabledBackward Defaults Change 80211 AntennaRestrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPortChange Buffering DefaultsNone See AlsoDefaults Bytes Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Session Limit Change Signal CheckChange Secondary Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect ParametersusernameParameterskeyword ForwardHostlist Show Hostlist command Initialize78 LAT ParametersDelayParametersserviceName Logout PortResume NetstatPing ParametershostnameParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show NetWare Show HostlistShow IPsecurity Show NodesShow Server Show PortsShow RS485 ParametersAllShow Session Show ServicesParametersBootparams Show Version Show SnmpShow Users SourceParametersSAPname 100 SPXTelnet Test ZeroProblem Report Procedure Full Contact InformationMultiple Strings UsageAvailable Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Leftmost Number Error BitsIntroduction 04000000 1000000008000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3