Lantronix MSS manual Change Backward Switch, Change Bootgateway

Page 23

Command Reference

Change Backward Switch

2.6 Change Backward Switch

 character 

CHANGE PORT PortList BACKWARD SWITCH   NONE 

Defines a key that will switch the user to a previous session without entering local mode. From local mode, the key functions as if the Backward command was entered. Any key can be specified unless it conflicts with MSS line editing or the Break or Forward keys. The key you specify will be stripped from the data stream, so while it won’t interfere with remote operating systems, you will lose any functionality that key would have on local programs.

Restrictions	Requires privileged user status.
Parameters	Port
	MSS4 only. Specifies a particular port or group of ports.
Note:	In the absence of the Portlist parameter, the configuration will affect the MSS4’s
	current port only.
	PortList
	Specify a particular port or group of ports. Port numbers are specified with
	integers between 1 and 4, and should be separated with commas (for lists) or
	dashes (for ranges).
	character
	Specifies a character to serve as the switch key. To specify a control character,
	use escaped hex (\xx). For example, Ctrl-B (ASCII character 0x02) would be
	specified as \02.
	None
	Clears any previously-defined Backward Switch key.
Defaults	No switch
See Also	Backward, page 2-2; Change Break, page 2-15; Change Forward Switch, page
	2-24; Change Local Switch, page 2-30; Forward, page 2-58.

2.7 Change Bootgateway

CHANGE SERVER BOOTGATEWAY IPaddress

Specifies the IP address of a server to send packets to when downloading code. Setting a bootgateway allows the MSS to download via a router without the router needing proxy arp support.

Note: A bootgateway host is not the loadhost—the packets will be addressed to the loadhost, but will be physically sent to the bootgateway host.

2-14

Image 23

Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change Change 80211 EnabledBackward Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Session Limit Change Signal CheckChange Secondary Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerParameterskeyword ForwardHostlist Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Session Show ServicesParametersBootparams Source Show SnmpShow Users Show VersionParametersSAPname 100 SPXTelnet Zero TestFull Contact Information Problem Report ProcedureMultiple Strings UsageAvailable Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Leftmost Number Error BitsIntroduction 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68