Lantronix MSS manual Change Loginpass, Change Modem Control

Page 40

Command Reference

Change Loginpass

2.31 Change Loginpass

CHANGE SERVER LOGINPASS passwd

Specifies the password used to log into the MSS. The password should consist of no more than 6 alphabetic letters. Users are only required to provide this password if the port has Password Protect enabled.

If you do not enter the password at the command line, you will immediately be prompted to enter the new password. This password is not displayed when typed.

Restrictions	Requires privileged user status.
Parameters	Server
	MSS4 only.
	passwd
	Enter a password of up to 6 alphabetic characters. When entered as part of the
	command, the password should be enclosed by quotation marks to preserve
	case.
Defaults	access
Examples	CHANGE LOGINPASS “badger”
See Also	Change Password Protect, page 2-38; Change Incoming, page 2-26.

2.32 Change Modem Control

 DISABLED 

CHANGE PORT PortList MODEM CONTROL   ENABLED 

Causes the MSS to treat any attached serial device as a modem. When enabled, a DSR drop will log out the enabled port and the MSS will drop DTR for three seconds and then raise it when the port logs out. If Autostart is also enabled, the port will not start until DSR is raised. The MSS supports partial modem control (DSR/DTR).

Restrictions	Requires privileged user status.
	Does not apply to the MSS485.
Errors	Modem Control must be disabled to use DSRLogout.
Parameters	Port
	MSS4 only. Specifies a particular port or group of ports.
Note:	In the absence of the PortList parameter, the configuration will affect the MSS4’s
	current port only.

2-31

Image 40

Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Backward Change 80211 EnabledChange Defaults Change 80211 AntennaRestrictions Errors Change 80211 FragmentationChange 80211 MAC Address ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPortDefaultsNone See Also Defaults BytesChange Buffering Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Secondary Change Signal CheckChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger ParametersusernameHostlist ForwardParameterskeyword Show Hostlist command InitializeParametersDelay ParametersserviceName78 LAT Logout PortNetstat PingResume Parametershostname84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show Hostlist Show IPsecurityShow NetWare Show NodesShow Ports Show RS485Show Server ParametersAllParametersBootparams Show ServicesShow Session Show Snmp Show UsersShow Version SourceTelnet 100 SPXParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationAvailable Strings UsageMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Introduction Error BitsLeftmost Number 10000000 0800000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3