Lantronix MSS manual Change Forward Switch, Change Gateway

Page 33

Command Reference

Change Forward Switch

2.19 Change Forward Switch

 character 

CHANGE PORT PortList FORWARD SWITCH 

 NONE 

Defines a key that will switch the user to the next session without entering local mode. In local mode, the key functions as if the Forward command was entered. Any key can be specified unless it conflicts with MSS line editing or the Break or Forward keys. The key you specify will be stripped from the data stream, so while it won’t interfere with remote operating systems, you will lose any functionality that key would have on local programs.

Restrictions	Requires privileged user status.
Parameters	Port
	MSS4 only. Specifies a particular port or group of ports.
Note:	In the absence of the PortList parameter, the configuration will affect the MSS4’s
	current port only.
	PortList
	Specify a particular port or group of ports. Port numbers are specified with
	integers between 1 and 4, and should be separated with commas (for lists) or
	dashes (for ranges).
	character
	Type a character to serve as the switch key. To specify a control character, use
	escaped hex (\xx). For example, Ctrl-B (ASCII character 0x02) would be
	specified as \02.
	None
	Clears the previously-defined Forward Switch key.
Defaults	No switch
See Also	Change Backward Switch, page 2-14; Change Break, page 2-15; Change Local
	Switch, page 2-30; Forward, page 2-58.

2.20 Change Gateway

CHANGE SERVER SECONDARY GATEWAY IPaddress

Specifies the host that is to be used as a TCP/IP gateway between networks. If a connection to a machine on a different network is attempted, messages will be directed to the gateway for forwarding. The MSS will try to learn gateways automatically if none have been configured.

Restrictions	Requires privileged user status.
Errors	If a gateway is not defined, an error will be returned.

2-24

Image 33

Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change 80211 Enabled BackwardChange Change 80211 Antenna DefaultsRestrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address ParametersExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchDefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPortDefaults Bytes DefaultsNone See AlsoChange Buffering Change CharsizeChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Signal Check Change SecondaryChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger ParametersusernameForward HostlistParameterskeyword Initialize Show Hostlist commandParametersserviceName ParametersDelay78 LAT Logout PortPing NetstatResume ParametershostnameRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show IPsecurity Show HostlistShow NetWare Show NodesShow RS485 Show PortsShow Server ParametersAllShow Services ParametersBootparamsShow Session Show Users Show SnmpShow Version Source100 SPX TelnetParametersSAPname Zero TestFull Contact Information Problem Report ProcedureUsage Available StringsMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Error Bits IntroductionLeftmost Number 08000000 1000000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68