Lantronix MSS manual Rlogin, 84 RTC, ParametersIPaddress

Page 71

Command Reference

Rlogin

2.83 Rlogin

RLOGIN IPaddress username

Attempts to log in to a remote host as a local user.

ParametersIPaddress

Specify a resolvable text host name or a numeric IP address. This parameter is optional if a preferred Telnet service has been defined.

username

Specify a name to be used as the login name.

2.84 RTC

Sets

RTC

SET

DATE date TIME time

SHOW

Sets the real time clock (RTC) on the MSSLite-A and MSSLiteX-A.

Restrictions

Only valid on the MSSLite-A and MSSLiteX-A.

Parameters

Set

 

Sets either the date or time.

 

Date

 

Sets the date. Must be used with the date parameter.

 

date

 

Enter the date as MM/DD/YY.

 

Time

 

Sets the time. Must be used with the time parameter.

 

time

 

Enter the time as HH:MM:SS.

 

Show

 

Shows the current RTC date and time settings.

Examples

Local_2>> RTC SET DATE 01/19/01

 

Local_2>> RTC SET TIME 17:01:16

 

Local_2>> RTC SHOW TIME

2-62

Image 71
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change Change 80211 EnabledBackward Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Session Limit Change Signal CheckChange Secondary Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerParameterskeyword ForwardHostlist Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Session Show ServicesParametersBootparams Source Show SnmpShow Users Show VersionParametersSAPname 100 SPXTelnet Zero TestFull Contact Information Problem Report ProcedureMultiple Strings UsageAvailable Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Leftmost Number Error BitsIntroduction 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68