Lantronix MSS manual Show Services, Show Session, ParametersBootparams

Page 75

Command Reference

Show Services

ParametersBootparams

Displays MSS parameters that relate to the boot procedure and software loadfile.

Counters

Displays Ethernet and TCP/IP error information.

Characteristics

Displays server settings including hardware address, timer limit, password limit, session limit, retransmit limit, IP address, subnet mask, nameserver, gateway, and more.

DefaultsCharacteristics

See Also

Status Displays, page 5-6.

2.94 Show Services

SHOW SERVICES [ serviceName]

Displays the characteristics of the LAT services on the network.

Restrictions

This list is masked by the service groups that the port is able to see. In other

 

words, users will not be able to see services to which they cannot connect.

Errors

Does not apply to MSSLite, MSS-VIA, or the MSS4.

Parameters

serviceName

 

Specify a service whose information you want to see. Wildcards are permitted.

 

All services will be shown if no service is specified.

See Also

Status Displays, page 5-6.

2.95 Show Session

SHOW SESSION

Displays information about the serial port’s current session(s). For the MSS4, this command shows the current session(s) for the current serial port.

See Also

Status Displays, page 5-6.

2-66

Image 75
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change 80211 Enabled BackwardChange Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Signal Check Change SecondaryChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerForward HostlistParameterskeyword Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Services ParametersBootparamsShow Session Source Show SnmpShow Users Show Version100 SPX TelnetParametersSAPname Zero TestFull Contact Information Problem Report ProcedureUsage Available StringsMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Error Bits IntroductionLeftmost Number 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68