Lantronix MSS manual Change Dhcp, Change Domain

Page 30

Command Reference

Change DHCP

2.14 Change DHCP

CHANGE		SERVER			DISABLED 
					DISABLED 
				DHCP 	
					ENABLED 
					ENABLED 

Enables or disables querying for a DHCP host at system boot time.

Restrictions	Requires privileged user status.
Errors	Configuring an IP address will automatically disable DHCP.
	Enabling DHCP will remove the IP address saved in non-volatile memory
	(NVR).
Parameters	Server
	MSS4 only.
Defaults	Enabled
See Also	The IP Address Configuration section of your Installation Guide.

2.15 Change Domain

CHANGE		SERVER			DomainName 
					DomainName 
				DOMAIN 		
					NONE	
					NONE	

Specifies the default domain name to be used when attempting to resolve text TCP/IP host names.

Restrictions	Requires privileged user status.
Parameters	Server
	MSS4 only.
	DomainName
	Enter a domain name of no more than 64 characters.
	None
	Disables the previously configured domain name.
See Also	Change Nameserver, page 2-33

2-21

Image 30

Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change 80211 Enabled BackwardChange Defaults Change 80211 AntennaRestrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPortChange Buffering DefaultsNone See AlsoDefaults Bytes Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Signal Check Change SecondaryChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect ParametersusernameForward HostlistParameterskeyword Show Hostlist command Initialize78 LAT ParametersDelayParametersserviceName Logout PortResume NetstatPing ParametershostnameRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show NetWare Show HostlistShow IPsecurity Show NodesShow Server Show PortsShow RS485 ParametersAllShow Services ParametersBootparamsShow Session Show Version Show SnmpShow Users Source100 SPX TelnetParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationUsage Available StringsMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Error Bits IntroductionLeftmost Number 04000000 1000000008000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3