Lantronix MSS manual Change 80211 Network Mode, Examples

Page 15

Command Reference

Change 80211

Restrictions

Requires privileged user status.

 

Only applies to the MSS-VIA and certain MSS4 models.

Errors

If you enter a command that is not applicable to the 802.11 card currently in

 

use, you will receive an Error message.

Parameters

Card

 

Instructs the MSS to use the MAC address of the wireless PC card that is

 

inserted into one of its PC card slots.

 

MSS

 

Instructs the MSS to use its own internal MAC address.

Defaults

MSS

Examples

Local>> CHANGE 80211 MACADDRESS CARD

 

Local>> CHANGE 80211 RESET

See Also

Show 80211, page 2-63

2.2.7 Change 80211 Network Mode

ADHOC

CHANGE 80211 NETWORKMODE

 

INFRASTRUCTURE

 

 

 

Denotes whether the MSS operates in a peer-to-peer (AdHoc) or managed (Infrastructure) network environment.

Any configuration changes you make will not take place until you issue the Change 80211 Reset command.

Restrictions

Requires privileged user status.

 

Only applies to the MSS-VIA and certain MSS4 models.

Errors

If you enter a command that is not applicable to the 802.11 card currently in

 

use, you will receive an Error message.

Parameters

AdHoc

 

Specifies that the MSS is communicating with other wireless devices in a peer-

 

to-peer capacity.

 

Infrastructure

 

Specifies that the MSS is communicating with an Access Point (AP).

Defaults

Infrastructure

Examples

Local>> CHANGE 80211 NETWORKMODE ADHOC

 

Local>> CHANGE 80211 RESET

See Also

Show 80211, page 2-63

2-6

Image 15
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change 80211 Enabled BackwardChange Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Signal Check Change SecondaryChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerForward HostlistParameterskeyword Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Services ParametersBootparamsShow Session Source Show SnmpShow Users Show Version100 SPX TelnetParametersSAPname Zero TestFull Contact Information Problem Report ProcedureUsage Available StringsMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Error Bits IntroductionLeftmost Number 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68