Lantronix MSS manual Set Privileged, Show, ParametersAntenna

Page 72

Command Reference

Set Privileged

2.85 Set Privileged

SET PRIVILEGED OVERRIDE

NOPRIVILEGED

Changes the port’s privileged status.

Note:

If you forget the password, you must reset the MSS to its factory defaults. See

 

Initialize on page 2-59for instructions.

Restrictions

Secure users may not become the privileged user.

 

Only one port at a time can be the privileged port.

Parameters

Privileged

 

Allows a user to become the port’s privileged user, provided the user enters the

 

correct password.

 

Override

 

Forces the current port to become the privileged port (the previous port loses

 

the privilege).

 

Noprivileged

 

Removes privileged status for the port.

See Also

Change Privpass, page 2-40.

2.86 Show 80211

SHOW 80211

ANTENNA

POWER

Displays the current wireless networking settings. Entering the command without any parameters displays basic 80211 settings including Region, MAC address, and ESSID. Also displayed are any 802.11 errors, which are discussed in Appendix B, Show 802.11 Errors.

Errors

Only applies to the MSS-VIA and MSS4.

ParametersAntenna

Displays the antenna diversity options (RX and TX) available on the currently installed 802.11 card.

Power

Displays, in milliWatts, the transmit power settings supported by the currently installed 802.11 card.

See Also

Change 80211, page 2-2; Show 802.11 Errors, page B-1.

2-63

Image 72
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change 80211 Enabled BackwardChange Defaults Change 80211 AntennaRestrictions Errors Change 80211 FragmentationChange 80211 MAC Address ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPortDefaultsNone See Also Defaults BytesChange Buffering Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Signal Check Change SecondaryChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger ParametersusernameForward HostlistParameterskeyword Show Hostlist command InitializeParametersDelay ParametersserviceName78 LAT Logout PortNetstat PingResume ParametershostnameRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Hostlist Show IPsecurityShow NetWare Show NodesShow Ports Show RS485Show Server ParametersAllShow Services ParametersBootparamsShow Session Show Snmp Show UsersShow Version Source100 SPX TelnetParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationUsage Available StringsMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Error Bits IntroductionLeftmost Number 10000000 0800000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3