Lantronix MSS manual Change IPAddress, Change IPSecurity

Page 36

Command Reference	Change IPAddress
	Password
	Prompts the user to enter the login password when attempting an incoming
	connection.
	Nopassword
	Allows incoming connections without prompting for the login password.
Defaults	Telnet, Nopassword
See Also	Change Loginpass, page 2-31.

2.24 Change IPAddress

CHANGE SERVER IPADDRESS IPaddress

Sets the MSS’s IP address. The IP address must be set before any TCP/IP functionality is available. The new IP address will take effect immediately.

Restrictions	Requires privileged user status.
Errors	You will receive an error if the MSS cannot use the specified IP address or if
	there are currently any network connections.
Parameters	Server
	MSS4 only.
	IPaddress
	Specify the IP address in standard numeric format.
See Also	Change DHCP, page 2-21; the Getting Started chapter of your Installation
	Guide.

2.25 Change IPSecurity

		BOTH			
					
				ENABLED	
		INCOMING			
CHANGE IPSECURITY IPaddress 					
CHANGE IPSECURITY IPaddress 				DISABLED	
		OUTGOING			
		PORTS	portlist		
		PORTS	portlist		

Adds entries to or edits entries in the IP Security table. The Ports parameter, applicable only to the MSS4, restricts connections to the given IP address from certain ports, and connections from this address to the specified ports.

2-27

Image 36

Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change 80211 Enabled BackwardChange Defaults Change 80211 AntennaRestrictions Errors Change 80211 FragmentationChange 80211 MAC Address ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPortDefaultsNone See Also Defaults BytesChange Buffering Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Signal Check Change SecondaryChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger ParametersusernameForward HostlistParameterskeyword Show Hostlist command InitializeParametersDelay ParametersserviceName78 LAT Logout PortNetstat PingResume ParametershostnameRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Hostlist Show IPsecurityShow NetWare Show NodesShow Ports Show RS485Show Server ParametersAllShow Services ParametersBootparamsShow Session Show Snmp Show UsersShow Version Source100 SPX TelnetParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationUsage Available StringsMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Error Bits IntroductionLeftmost Number 10000000 0800000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3