Lantronix MSS manual Change LAT CircTimer

Page 37

Command Reference	Change LAT CircTimer
Restrictions	Requires privileged user status.
	The Both, Incoming, and Outgoing parameters are only applicable to the
	MSS4.
Parameters	IPaddress
	Specify an address in standard numeric format. An address with 0 or 255 in any
	segment restricts all addresses in that range.
	Both
	MSS4 only. Restricts logins from the network into the server and TCP sessions
	to the network from the server.
	Incoming
	MSS4 only. Restricts logins from the network into the server, and connections
	to the serial port.
	Outgoing
	MSS4 only. Restricts TCP sessions to the network from the server.
	Ports
	MSS4 only. Specifies a particular port or group of ports.
	PortList
	Specify a particular port or group of ports. Port numbers are specified with
	integers between 1 and 4, and should be separated with commas (for lists) or
	dashes (for ranges). If a portlist is not specified, all physical and virtual ports
	apply.
Defaults	Disabled
Examples	Change IPsecurity 192.0.220.77 Disabled
	(Restricts the single IP address from the table.)
	Change IPsecurity 192.0.1.255 Both Disabled
	(MSS4 only: Restricts all addresses between 192.0.1.0 and 192.0.1.255 from both
	incoming and outgoing connections.)

2.26 Change LAT CircTimer

CHANGE LAT CIRCTIMER timerValue

Specifies the delay between messages sent from the MSS to other network nodes. This parameter should not need to be altered, and should not be altered when there are active sessions.

Restrictions	Requires privileged user status.
Errors	The MSSLite, MSS4, and the MSS-VIA do not support LAT.
Parameters	timerValue
	Specify a value from 30 to 200 milliseconds.
Defaults	80 (milliseconds)
	2-28

Image 37

Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Backward Change 80211 EnabledChange Change 80211 Antenna DefaultsRestrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address ParametersExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchDefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPortDefaults Bytes DefaultsNone See AlsoChange Buffering Change CharsizeChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger ParametersusernameHostlist ForwardParameterskeyword Initialize Show Hostlist commandParametersserviceName ParametersDelay78 LAT Logout PortPing NetstatResume Parametershostname84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show IPsecurity Show HostlistShow NetWare Show NodesShow RS485 Show PortsShow Server ParametersAllParametersBootparams Show ServicesShow Session Show Users Show SnmpShow Version SourceTelnet 100 SPXParametersSAPname Zero TestFull Contact Information Problem Report ProcedureAvailable Strings UsageMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Introduction Error BitsLeftmost Number 08000000 1000000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68