Lantronix MSS manual Change Modem Emulation, Change Name

Page 41

Command Reference

Change Modem Emulation

PortList

Specify a particular port or group of ports. Port numbers are specified with integers between 1 and 4, and should be separated with commas (for lists) or dashes (for ranges).

DefaultsDisabled

See Also

Change Autostart, page 2-12;Change DSRLogout, page 2-22.

2.33 Change Modem Emulation

 DISABLED 

CHANGE PORT PortList MODEM EMULATION   ENABLED 

Presents a modem interface to an attached serial device. The MSS can then accept AT-style modem commands and handle the modem signals correctly. See your Installation Guide for more details on modem emulation.

Note:	If the MSS is in modem emulation mode and a serial port is idle, the MSS can still
	accept network TCP connections to that serial port.
Restrictions	Requires privileged user status.
	Does not apply to the MSS485.

Parameters

Note:

Port

MSS4 only. Specifies a particular port or group of ports.

In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

PortList

	Specify a particular port or group of ports. Port numbers are specified with
	integers between 1 and 4, and should be separated with commas (for lists) or
	dashes (for ranges).
Defaults	Disabled
See Also	Change Autostart, page 2-12; the Using the MSS chapter of your Installation
	Guide

2.34 Change Name

CHANGE SERVER NAME serverName

Renames the MSS. The unit’s default name, which is based on its default Ethernet address, is printed on its underside. This name is what will be advertised if WINS is enabled.

Restrictions

Requires privileged user status.

2-32

Image 41

Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change Change 80211 EnabledBackward Change 80211 Antenna DefaultsRestrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address ParametersExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchDefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPortDefaults Bytes DefaultsNone See AlsoChange Buffering Change CharsizeChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Session Limit Change Signal CheckChange Secondary Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger ParametersusernameParameterskeyword ForwardHostlist Initialize Show Hostlist commandParametersserviceName ParametersDelay78 LAT Logout PortPing NetstatResume ParametershostnameParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show IPsecurity Show HostlistShow NetWare Show NodesShow RS485 Show PortsShow Server ParametersAllShow Session Show ServicesParametersBootparams Show Users Show SnmpShow Version SourceParametersSAPname 100 SPXTelnet Zero TestFull Contact Information Problem Report ProcedureMultiple Strings UsageAvailable Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Leftmost Number Error BitsIntroduction 08000000 1000000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68