Lantronix MSS manual Change Verify, Change Wins

Page 60

Command Reference

Change Verify

2.67 Change Verify

DISABLED

CHANGE PORT PortList VERIFY   ENABLED

Controls whether the MSS will provide informational messages whenever a session is connected, disconnected, or switched.

Restrictions

Requires privileged user status.

 

If a port is Dedicated, Verify is disabled.

Parameters

Note:

Port

MSS4 only. Specifies a particular port or group of ports.

In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

PortList

Specify a particular port or group of ports. Port numbers are specified with integers between 1 and 4, and should be separated with commas (for lists) or dashes (for ranges).

DefaultsEnabled

2.68 Change WINS

DISABLED

CHANGE SERVER WINS   ENABLED

Allows the MSS to broadcast a WINS name announcement at boot time, and answer broadcast WINS name queries. This setting allows other hosts to locate the MSS.

Restrictions

Requires privileged user status.

ParametersServer

MSS4 only.

DefaultsDisabled

2-51

Image 60
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change 80211 Enabled BackwardChange Defaults Change 80211 AntennaRestrictions Errors Change 80211 FragmentationChange 80211 MAC Address ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPortDefaultsNone See Also Defaults BytesChange Buffering Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Signal Check Change SecondaryChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger ParametersusernameForward HostlistParameterskeyword Show Hostlist command InitializeParametersDelay ParametersserviceName78 LAT Logout PortNetstat PingResume ParametershostnameRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Hostlist Show IPsecurityShow NetWare Show NodesShow Ports Show RS485Show Server ParametersAllShow Services ParametersBootparamsShow Session Show Snmp Show UsersShow Version Source100 SPX TelnetParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationUsage Available StringsMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Error Bits IntroductionLeftmost Number 10000000 0800000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3