Lantronix MSS manual Show Hostlist, Show IPsecurity, Show NetWare, Show Nodes, ParametersLAT

Page 73

Command Reference

Show Hostlist

2.87 Show Hostlist

SHOW HOSTLIST

Displays the current list of remote hosts to use for multihost mode connections.

See Also

Status Displays, page 5-6;Multihost Mode, page 5-11; Hostlist, page 2-58.

2.88 Show IPsecurity

SHOW IPSECURITY

Displays the current TCP/IP security table. Each address or range is shown, along with the direction of concern.

See Also

Status Displays, page 5-6.

2.89 Show NetWare

SHOW NETWARE

Displays NetWare characteristics, including frame types, routing status, and internal network number.

Errors	Does not apply to MSSLite, MSS-VIA, or the MSS4.
See Also	Status Displays, page 5-6.

2.90 Show Nodes

 LAT 

SHOW NODES    SPX 

Displays information about the desired LAT or SPX service nodes.

ErrorsAll nodes will be shown if no node is specified.

Does not apply to the MSS-Via, MSS4, or MSSLite.

ParametersLAT

Shows LAT nodes identification strings and availability.

2-64

Image 73

Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Backward Change 80211 EnabledChange Change 80211 Antenna DefaultsRestrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address ParametersExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchDefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPortDefaults Bytes DefaultsNone See AlsoChange Buffering Change CharsizeChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger ParametersusernameHostlist ForwardParameterskeyword Initialize Show Hostlist commandParametersserviceName ParametersDelay78 LAT Logout PortPing NetstatResume Parametershostname84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show IPsecurity Show HostlistShow NetWare Show NodesShow RS485 Show PortsShow Server ParametersAllParametersBootparams Show ServicesShow Session Show Users Show SnmpShow Version SourceTelnet 100 SPXParametersSAPname Zero TestFull Contact Information Problem Report ProcedureAvailable Strings UsageMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Introduction Error BitsLeftmost Number 08000000 1000000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68