Lantronix MSS manual Unassigned

Page 87

Show 802.11 Errors

Rightmost Number

00100000

Unassigned.

00080000

Unassigned.

00040000

Unassigned.

00020000

Internal error. May occur on some cards in conjunction with other described

 

error codes.

00010000

The 802.11 card in use is not compatible with the regulatory region to which

 

the unit has been programmed.

00008000

Internal error.

00004000

Internal error. May occur on some cards in conjunction with authentication or

 

association failures, or other configuration mismatches.

00002000

Received an 802.11 packet that was too large to be handled.

00001000

Internal error.

00000800

Failed to queue a data packet that could not be sent immediately for later

 

transmission. It was dropped.

00000400

Internal error.

00000200

Failed to find, sync to, and associate with an AP or ad-hoc network within a

 

reasonable time. Most likely there is no AP or ad-hoc network within range

 

that satisfies the unit's ESSID, NETWORK-TYPE, and CHANNEL

 

parameters.

00000100

Received an 802.11 data packet that was not encapsulated as per RFC1042 or

 

802.1h. Unit will still decapsulate and interpret the packet. Some vendors'

 

APs trip this error when they send out "magic packets" containing proprietary

 

extensions not defined by the 802.11 spec.

00000080

Received an 802.11 data packet encapsulated in a completely foreign manner,

 

or not encapsulated at all. Unit will still attempt to interpret the packet, but

 

proper interpretation is not guaranteed. The packet may be dropped as

 

unintelligible.

00000040

Received an encrypted packet that could not properly be decrypted. Packet

 

was dropped.

00000020

Unspecified error during packet reception. At least one packet was dropped.

 

Absence of this error bit does not imply that all packets have been received

 

correctly, however.

00000010

A received packet failed CRC check and was dropped.

00000008

Internal error. May occur in conjunction with "no AP or ad-hoc network

 

within range" errors.

B-4

Image 87
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change 80211 Enabled BackwardChange Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Signal Check Change SecondaryChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerForward HostlistParameterskeyword Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Services ParametersBootparamsShow Session Source Show SnmpShow Users Show Version100 SPX TelnetParametersSAPname Zero TestFull Contact Information Problem Report ProcedureUsage Available StringsMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Error Bits IntroductionLeftmost Number 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68