Lantronix MSS manual Change 80211 WEP

Page 18

Command ReferenceChange 80211

Parameters

num

 

 

Enter a value between 0 and 3000.

Defaults

3000

 

Examples

Local>> CHANGE 80211

RTS 0

 

Local>> CHANGE 80211

RESET

See Also

Show 80211, page 2-63

2.2.12 Change 80211 WEP

 

 

 

ENABLED

 

 

DISABLED

 

 

 

 

 

INDEX num

 

CHANGE 80211 WEP

KEY keydata

 

 

 

ALL

RECEIVE

 

ENCRYPTED

 

 

 

 

 

 

 

 

Enabling WEP (Wireless Equivalent Privacy) means the MSS will only connect to an AP (in infrastructure mode) or communicate with other ad-hoc peers (in ad-hoc mode) that have been programmed with the same WEP key as the MSS. All wireless network traffic the MSS sends will be encrypted with its WEP key and any encrypted wireless network traffic the MSS receives will be decrypted with its WEP key. Disabling WEP causes the MSS to ignore its WEP key and only receive and transmit unencrypted network traffic.

Any configuration changes you make will not take place until you issue the Change 80211 Reset command.

Restrictions

Requires privileged user status.

 

Only applies to the MSS-VIA and certain MSS4 models.

Errors

If you enter a command that is not applicable to the 802.11 card currently in

 

use, you will receive an Error message.

Parameters

Enabled

 

Enables WEP.

 

Disabled

 

Disables WEP.

 

Index

 

Assigns the index number that should be used with the WEP key.

 

num

 

Enter an integer between 1 and 4. For two keys to match, both their key data

 

and their index number must be identical.

 

Key

 

Sets the WEP key. The MSS allows both 40-bit and 128-bit keys, and will

 

determine which key length is being set by the length of the key data.

2-9

Image 18
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change 80211 Enabled BackwardChange Defaults Change 80211 AntennaRestrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPortChange Buffering DefaultsNone See AlsoDefaults Bytes Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostChange NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Signal Check Change SecondaryChange Session Limit Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersDefaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect ParametersusernameForward HostlistParameterskeyword Show Hostlist command Initialize78 LAT ParametersDelayParametersserviceName Logout PortResume NetstatPing ParametershostnameRlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show NetWare Show HostlistShow IPsecurity Show NodesShow Server Show PortsShow RS485 ParametersAllShow Services ParametersBootparamsShow Session Show Version Show SnmpShow Users Source100 SPX TelnetParametersSAPname Test ZeroProblem Report Procedure Full Contact InformationUsage Available StringsMultiple Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Error Bits IntroductionLeftmost Number 04000000 1000000008000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3