Lantronix MSS manual Change Stopbits, Change Subnet Mask, Defaults See Also

Page 56

Command Reference

Change Stopbits

 

num

 

Specify the desired number or retry attempts. Enter zero to make the MSS retry

 

until the startupfile is read (indefinitely).

Defaults

Retry: 5

Examples

Local> CHANGE STARTUP FILE “bob:start”

 

Local> CHANGE STARTUP FILE hevax::start.com

 

Local> CHANGE STARTUP FILE “engfs\sys:\login\start.cmd”

 

Local> CHANGE SERVER STARTUP RETRY 6

See Also

Change Loadhost, page 2-29; Source, page 2-67.

2.60 Change Stopbits

CHANGE

 

PORT PortList

 

1

 

 

 

 

STOPBITS

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

Specifies how many stop bits the port will use.

Restrictions

Requires privileged user status.

Parameters

Port

 

MSS4 only. Specifies a particular port or group of ports.

Note:

In the absence of the PortList parameter, the configuration will affect the MSS4’s

 

current port only.

 

PortList

 

Specify a particular port or group of ports. Port numbers are specified with

 

integers between 1 and 4, and should be separated with commas (for lists) or

 

dashes (for ranges).

Defaults

1

See Also

Change Autobaud, page 2-11; Change Charsize, page 2-16; Change Parity,

 

page 2-35.

2.61 Change Subnet Mask

CHANGE

SERVER

SUBNET MASK mask

Sets an IP subnet mask for the MSS. The mask is applied to target IP addresses to determine whether the destination address is on the local network segment. If the address is not on the local segment, the MSS’s gateway host will be accessed to provide the connection. A mask is created by default when the IP address is first set, but can be overridden with this command.

2-47

Image 56
Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change Change 80211 EnabledBackward Defaults Change 80211 AntennaRestrictions Errors Change 80211 FragmentationChange 80211 MAC Address ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPortDefaultsNone See Also Defaults BytesChange Buffering Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Session Limit Change Signal CheckChange Secondary Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger ParametersusernameParameterskeyword ForwardHostlist Show Hostlist command InitializeParametersDelay ParametersserviceName78 LAT Logout PortNetstat PingResume ParametershostnameParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Hostlist Show IPsecurityShow NetWare Show NodesShow Ports Show RS485Show Server ParametersAllShow Session Show ServicesParametersBootparams Show Snmp Show UsersShow Version SourceParametersSAPname 100 SPXTelnet Test ZeroProblem Report Procedure Full Contact InformationMultiple Strings UsageAvailable Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Leftmost Number Error BitsIntroduction 10000000 0800000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3