Lantronix MSS manual Change Timeserver, Daytime is only supported over UDP

Page 59

Command Reference

Change Timeserver

2.66 Change Timeserver

 

 

 

 

 

DAYTIME

 

 

 

 

 

 

 

 

 

 

 

GMTOFFSET num

 

 

 

 

 

 

 

 

 

 

 

NONE

 

CHANGE

 

SERVER

 

 

 

TIMESERVER

 

 

 

 

 

BROADCAST

 

 

 

 

 

 

 

 

NTP

IP ipaddress

 

 

 

 

 

 

 

 

PASSIVE

 

 

 

 

 

 

 

 

 

 

 

 

 

Specifies which timeserver the MSS will use to update its internal clock. The MSS can communicate with either Daytime or Network Timeserver Protocol (NTP) servers. For NTP, the MSS can periodically broadcast a message asking for time information and wait for an NTP timeserver to reply, periodically query a specific NTP timeserver, or just listen for NTP broadcasts on the network.

Parameters

Server

 

MSS4 only.

 

Daytime

 

Specifies a daytime server. The MSS will listen for a possible daytime server,

 

then send packets querying that server for time information.

Note:

Daytime is only supported over UDP.

 

GMTOffset

 

Specifies the local timezone’s difference from Greenwich Mean Time (GMT).

 

num

 

Enter a value from -12 to +13. For example, the GMTOffset for Los Angeles,

 

CA, USA would be -8 (PST) or -7 (PDT).

 

None

 

Clears a previous timeserver setting, but does not clear the GMTOffset setting.

 

NTP

 

Specifies an NTP server. There are three types of NTP.

 

Broadcast

 

The MSS periodically broadcasts a message that asks for time information, and

 

waits for an NTP timeserver to reply.

 

IP

 

Use this method if you have a single NTP timeserver on your network. You

 

must enter an IP address in standard numeric format.

 

Passive

 

The MSS will listen for NTP timeserver announcements on the network.

Examples

CHANGE TIMESERVER NTP IP 192.0.1.122

 

CHANGE TIMESERVER GMTOFFFSET -7

2-50

Image 59
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change Change 80211 EnabledBackward Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Session Limit Change Signal CheckChange Secondary Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerParameterskeyword ForwardHostlist Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Session Show ServicesParametersBootparams Source Show SnmpShow Users Show VersionParametersSAPname 100 SPXTelnet Zero TestFull Contact Information Problem Report ProcedureMultiple Strings UsageAvailable Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Leftmost Number Error BitsIntroduction 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68