Lantronix MSS manual Change NetWare Routing, Change Parity, Parametersfileserver

Page 44

Command Reference

Change NetWare Routing

Parametersfileserver

Enter the name of the desired fileserver using no more than 8 characters.

None

Specifies that no loadhost will be used.

See Also

Change Software, page 2-45.

2.39 Change NetWare Routing

 DISABLED 

CHANGE NETWARE ROUTING   ENABLED 

Allows the MSS to act as an internal router whenever there are multiple NetWare frame types in use on the LAN.

Restrictions	Requires privileged user status.
	The MSSLite, MSS4, and the MSS-VIA do not support Netware.
Defaults	Enabled
See Also	Change NetWare Encapsulation, page 2-33; Change NetWare Internal
	Network, page 2-34; Show NetWare, page 2-64.

2.40 Change Parity

			
			EVEN 
			
			MARK 
CHANGE	PORT PortList	PARITY 	NONE 
			
			ODD 
			
			SPACE 

Sets the parity for the specified serial port.

Restrictions	Requires privileged user status.
Errors	Parity must be None for the MSS100 and MSS-VIA to use 8-bit characters.
	Autobaud will not work unless the port is using 8 bit characters with No parity
	or 7 bit characters with Even parity.

2-35

Image 44

Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change Change 80211 EnabledBackward Defaults Change 80211 AntennaRestrictions Errors Change 80211 FragmentationChange 80211 MAC Address ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPortDefaultsNone See Also Defaults BytesChange Buffering Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Session Limit Change Signal CheckChange Secondary Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger ParametersusernameParameterskeyword ForwardHostlist Show Hostlist command InitializeParametersDelay ParametersserviceName78 LAT Logout PortNetstat PingResume ParametershostnameParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Hostlist Show IPsecurityShow NetWare Show NodesShow Ports Show RS485Show Server ParametersAllShow Session Show ServicesParametersBootparams Show Snmp Show UsersShow Version SourceParametersSAPname 100 SPXTelnet Test ZeroProblem Report Procedure Full Contact InformationMultiple Strings UsageAvailable Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Leftmost Number Error BitsIntroduction 10000000 0800000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3