Lantronix MSS manual Change Password Protect, Change Portname

Page 47

Command Reference

Change Password Protect

2.44 Change Password Protect

DISABLED

CHANGE PORT PortList PASSWORD PROTECT   ENABLED

Controls whether a password is needed to log into the MSS from a serial port. For models with a dedicated console port (the MSS-Via, MSS485, and the MSSLite A and C), this command will also affect the serial console port. To set the login password, use the Change Loginpass command.

Restrictions

Requires privileged user status.

ParametersPort

MSS4 only. Specifies a particular port or group of ports.

Note: In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

PortList

Specify a particular port or group of ports. Port numbers are specified with integers between 1 and 4, and should be separated with commas (for lists) or dashes (for ranges).

DefaultsDisabled

See Also

Change Loginpass, page 2-31.

2.45 Change Portname

CHANGE PORT PortList PORTNAME name

Renames the specified serial port.

Restrictions

Requires privileged user status.

Parameters

Port

 

MSS4 only. Specifies a particular port or group of ports.

Note:

In the absence of the PortList parameter, the configuration will affect the MSS4’s

 

current port only.

 

PortList

 

Specify a particular port or group of ports. Port numbers are specified with

 

integers between 1 and 4, and should be separated with commas (for lists) or

 

dashes (for ranges).

 

name

 

Enter a 16-character name composed of alphanumeric characters or the

 

underscore character. Enclose the name in quotation marks to preserve case.

Defaults

Port_1 (also Port_2, Port_3, and Port_4 for MSS4 only)

 

2-38

Image 47
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Change Change 80211 EnabledBackward Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Session Limit Change Signal CheckChange Secondary Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerParameterskeyword ForwardHostlist Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing ResumeParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerShow Session Show ServicesParametersBootparams Source Show SnmpShow Users Show VersionParametersSAPname 100 SPXTelnet Zero TestFull Contact Information Problem Report ProcedureMultiple Strings UsageAvailable Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Leftmost Number Error BitsIntroduction 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68