Lantronix MSS manual Command Line Editing, Key Purpose

Page 8

Introduction

Command Line Editing

Please read this section carefully so you can understand the conventions used in the command descriptions.

◆Commands are listed in alphabetical order.

◆Some commands do not apply to all members of the MSS family, and are so noted.

◆Commands and keywords appear in BOLD face.

◆User-entered parameters appear in italics. You must replace the italicized word.

When entering a parameter that is case-sensitive, such as file and host names, enclose the parameter in quotes to preserve case.

◆The Port portlist and Server parameters currently only apply to commands issued for the MSS4. Read each command carefully for more details.

◆When two or more parameters appear in curly braces {}, you must choose one and only one of the items within each set of braces to complete the command.

◆Parameters that appear in brackets [] are optional. If more than one parameter appears in a single set of brackets, only one parameter may be chosen at a time. Single parameters enclosed in brackets may be omitted from the command, or used in combination with one another.

◆The MSS has a reduced command set from the EPS, ETS, and MPS product lines. Change commands replace the Set/Define Server and Set/Define Port commands used in the earlier products.

A single Change command will take effect immediately (like a Set command), and will remain in effect until another Change command is issued (like a Define command). The exceptions are the Change Port and Set Privileged commands, which do not take effect until the port is logged out.

1.3 Command Line Editing

The following table lists keys that can be used for command line editing.

Table 1-1:Command Line Editing Keys

Key	Purpose


Return	Executes the current command line
Delete	Deletes the character before the cursor
Ctrl-A	Toggles insertion mode (insert or overstrike)
Ctrl-D	Logs the user out of the server
Ctrl-E	Moves the cursor to the end of the line
Ctrl-H or Backspace	Moves the cursor to the beginning of the line
Ctrl-R	Redisplays the current command
Ctrl-U	Deletes the entire line

1-2

Image 8

Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change Change 80211 EnabledBackward Defaults Change 80211 AntennaRestrictions Errors Change 80211 FragmentationChange 80211 MAC Address ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPortDefaultsNone See Also Defaults BytesChange Buffering Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Session Limit Change Signal CheckChange Secondary Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger ParametersusernameParameterskeyword ForwardHostlist Show Hostlist command InitializeParametersDelay ParametersserviceName78 LAT Logout PortNetstat PingResume ParametershostnameParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Hostlist Show IPsecurityShow NetWare Show NodesShow Ports Show RS485Show Server ParametersAllShow Session Show ServicesParametersBootparams Show Snmp Show UsersShow Version SourceParametersSAPname 100 SPXTelnet Test ZeroProblem Report Procedure Full Contact InformationMultiple Strings UsageAvailable Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Leftmost Number Error BitsIntroduction 10000000 0800000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3