Lantronix MSS manual Show Ports, Show RS485, Show Server, ParametersAll

Page 74

Command Reference

Show Ports

SPX

Shows SPX node hop counts, frame types, and availability.

See Also

Status Displays, page 5-6.

2.91 Show Ports

SHOW PORTS

ALL

PortList

Displays all serial port settings, including the port’s connection status, the flow control state , the state of DSR and DTR serial signals, the access type, and more. Can also be used to display modem card information (for the MSS-Via, Port 3; for the MSS4, Ports 5 and 6).

ParametersAll

MSS4 only. Shows the port settings on all serial ports.

PortList

MSS4 and MSSVia only. Port numbers are specified with integers between 1 and 4. Port numbers should be separated with commas (for lists) or dashes (for ranges).

See Also

Status Displays, page 5-6.

2.92 Show RS485

SHOW RS485

Displays the current RS-485 networking settings, including wire mode, termination, and TXDrive.

Errors	Only applies to the MSS-VIA and MSS4.
See Also	Change RS485, page 2-42.

2.93 Show Server

SHOW SERVER

BOOTPARAMS

COUNTERS

CHARACTERISTICS

Displays different types of MSS information. If you do not enter a parameter, the MSS will display general server characteristics .

2-65

Image 74

Contents MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s NewCommand Line Editing Key PurposeHelp About This ManualCommand Reference Change Change 80211 EnabledBackward Defaults Change 80211 AntennaRestrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation ParametersChange 80211 Network Mode ExamplesChange 80211 Power Change 80211 RegionChange 80211 Reset Change 80211 RTSChange 80211 WEP Change Access Current port onlyDefaultsDynamic See Also Change AutobaudChange Autostart Dashes for ranges Change Backward Switch Change BootgatewayChange Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPortChange Buffering DefaultsNone See AlsoDefaults Bytes Change CharsizeChange Datasend Condition has been detected Change Dedicated RestrictionsCommand on Change Dhcp Change DomainChange DSRLogout Change DTRWaitDefaultsDisabled Change Flow ControlChange Forward Switch Change GatewayChange Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPAddress Change IPSecurityChange LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Loginpass Change Modem ControlChange Modem Emulation Change NameChange Nameserver Change NetWare EncapsulationChange NetWare Internal Network Change NetWare LoadhostParametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Incoming Change Password LimitChange Password Protect Change PortnameChange Preferred Change Privpass Change RarpChange Rlogin Change Retransmit LimitChange RS485 Change Session Limit Change Signal CheckChange Secondary Change Silentboot Change SNMPSetCommChange Software Change SpeedChange Startup Two colons and the startup file name of up to 47 charactersChange Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Change Timeserver Daytime is only supported over UDPChange Verify Change WinsCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect ParametersusernameParameterskeyword ForwardHostlist Show Hostlist command Initialize78 LAT ParametersDelayParametersserviceName Logout PortResume NetstatPing ParametershostnameParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show NetWare Show HostlistShow IPsecurity Show NodesShow Server Show PortsShow RS485 ParametersAllShow Session Show ServicesParametersBootparams Show Version Show SnmpShow Users SourceParametersSAPname 100 SPXTelnet Test ZeroProblem Report Procedure Full Contact InformationMultiple Strings UsageAvailable Strings Usage Examples Xxxx1.5 or ParametersS1.11 Y Leftmost Number Error BitsIntroduction 04000000 1000000008000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWareTelnet 2-48,2-68 UDP 2-50,B-3