Lantronix MSS manual Change Buffering, Change Charsize, DefaultsNone See Also, Defaults Bytes

Page 25

Command Reference

Change Buffering

Remote

The MSS ignores the Break key and passes it to the remote host. Only applicable if the session protocol supports Break events. Telnet supports Break events, but Rlogin, raw TCP, and UDP do not.

None

Disables the Break key.

DefaultsNone

See Also

Change Local Switch, page 2-30.

2.10 Change Buffering

CHANGE SERVER BUFFERING buffersize

Specifies the size of the buffer (in bytes) to use for network connections. The default size should be sufficient in most cases.

Restrictions

Requires privileged user status.

ParametersServer

MSS4 only.

buffersize

Specify a size from 128 to 4096 (bytes).

Defaults

4096 bytes

2.11 Change Charsize

 

 

CHANGE

PORT PortList

CHARSIZE

7

 

 

8

 

 

 

 

Sets the number of data bits per character for the specified serial port.

Restrictions

Requires privileged user status.

Errors

Autobaud will only work when a port is set for 8 data bits with No parity or for

 

7 data bits with Even parity.

 

The MSS100 can only use charsize 8 when parity is set to None. The MSS4

 

and MSS-VIA can have any parity with charsize 8.

Parameters

Note:

Port

MSS4 only. Specifies a particular port or group of ports.

In the absence of the Portlist parameter, the configuration will affect the MSS4’s current port only.

2-16

Image 25
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Backward Change 80211 EnabledChange Change 80211 Antenna DefaultsRestrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address ParametersExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchDefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPortDefaults Bytes DefaultsNone See AlsoChange Buffering Change CharsizeChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger ParametersusernameHostlist ForwardParameterskeyword Initialize Show Hostlist commandParametersserviceName ParametersDelay78 LAT Logout PortPing NetstatResume Parametershostname84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show IPsecurity Show HostlistShow NetWare Show NodesShow RS485 Show PortsShow Server ParametersAllParametersBootparams Show ServicesShow Session Show Users Show SnmpShow Version SourceTelnet 100 SPXParametersSAPname Zero TestFull Contact Information Problem Report ProcedureAvailable Strings UsageMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Introduction Error BitsLeftmost Number 08000000 1000000004000000 02000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68