Lantronix MSS manual Change Access, Current port only

Page 19

Command Reference

Change Access

keydata

Enter the WEP key. The key format should be entered as “xx-xx-xx-xx...” where each x is a hexadecimal digit (0 through 9 and A through F). Each pair of hex digits (xx) defines a byte of key data, and each byte is separated from the next by a dash. For a 40-bit key, 5 bytes of key data must be given. For a 128-bit key, 13 bytes of data must be given.

Receive

Determines whether the MSS will receive unencrypted data while WEP is enabled.

All

Allows reception of encrypted traffic while WEP is enabled. The MSS will accept unencrypted wireless network frames, as well as frames encrypted with its WEP key. This is the default setting once WEP has been enabled.

Encrypted

Refuses to accept unencrypted data while WEP is enabled. The MSS will discard and ignore unencrypted wireless network frames, accepting only frames encrypted with its WEP key.

Defaults

Disabled, Receive all

 

Examples

Local>> CHANGE 80211 WEP ENABLED

 

Local>> CHANGE 80211

WEP INDEX 3

 

Local>> CHANGE 80211

WEP RECEIVE ENCRYPTED

 

Local>> CHANGE 80211

RESET

See Also

Show 80211, page 2-63

2.3 Change Access

 

 

 

 

LOCAL

 

 

 

 

CHANGE

 

PORT PortList

 

DYNAMIC

 

 

 

 

ACCESS

 

 

 

 

 

REMOTE

 

 

 

 

 

 

 

 

NONE

 

 

 

 

 

 

 

 

 

 

 

Specifies which types of connections the specified serial port will accept.

Restrictions

Requires privileged user status.

 

The None parameter is only valid for the MSS4.

 

Autobaud must be disabled for ports set to Dynamic and Remote access.

Errors

If a port is active, its access can not be changed.

Parameters

Port

 

MSS4 only. Specifies a particular port or group of ports.

Note:

In the absence of the Portlist parameter, the configuration will affect the MSS4’s

 

current port only.

2-10

Image 19
Contents MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command SyntaxKey Purpose Command Line EditingAbout This Manual HelpCommand Reference Backward Change 80211 EnabledChange Change 80211 Antenna DefaultsRestrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC AddressExamples Change 80211 Network ModeChange 80211 Region Change 80211 PowerChange 80211 RTS Change 80211 ResetChange 80211 WEP Current port only Change AccessChange Autobaud DefaultsDynamic See AlsoChange Autostart Dashes for ranges Change Bootgateway Change Backward SwitchRestrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change BreakChange Charsize DefaultsNone See AlsoDefaults Bytes Change BufferingChange Datasend Condition has been detected Restrictions Change DedicatedCommand on Change Domain Change DhcpChange DTRWait Change DSRLogoutChange Flow Control DefaultsDisabledChange Gateway Change Forward SwitchDefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddressChange LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change LoginpassChange Name Change Modem EmulationChange NetWare Encapsulation Change NameserverChange NetWare Loadhost Change NetWare Internal NetworkChange Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password IncomingChange Portname Change Password ProtectChange Preferred Change Rarp Change PrivpassChange Retransmit Limit Change RloginChange RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change SilentbootChange Speed Change SoftwareTwo colons and the startup file name of up to 47 characters Change StartupChange Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change TimeserverChange Wins Change VerifyCrypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect FingerHostlist ForwardParameterskeyword Initialize Show Hostlist commandLogout Port ParametersDelayParametersserviceName 78 LATParametershostname NetstatPing Resume84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWareParametersAll Show PortsShow RS485 Show ServerParametersBootparams Show ServicesShow Session Source Show SnmpShow Users Show VersionTelnet 100 SPXParametersSAPname Zero TestFull Contact Information Problem Report ProcedureAvailable Strings UsageMultiple Strings Xxxx Usage ExamplesParametersS 1.5 or1.11 Y Introduction Error BitsLeftmost Number 02000000 1000000008000000 04000000Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37UDP 2-50,B-3 Telnet 2-48,2-68